Reviewed by the Benton Metal Depot team · Updated
Do you have one horse, or several of them? It's important that the barn is suitable for both the animals and the people caring for them. Benton Metal Depot serves customers in Fendig and throughout Brantley with agricultural metal building materials, including 29-gauge and 26-gauge Rib panels panels for applicable barn packages.
Key Points
- ◦The current local setback for a horse barn in Fendig is Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts..
- ◦Aisle width should allow horses and handlers to move comfortably and safely.
- ◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
- ◦Plan stall dimensions around the horses that will actually use them.
- ◦Horse barn exterior materials are available in 7 colors.
At a Glance
| Permit threshold |
Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.
As of 2026 · Source |
| Wind load zone |
Inland/near-coastal Georgia (Nahunta) — roughly 115-125 mph (ASCE 7, Exposure C); Brantley County sits just inland of the coastal GA counties (Camden/Glynn) so its mapped speed is likely somewhat lower than the ~130 mph coastal band but higher than deep-interior GA. NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels
As of 2026 · Source |
| Drive time from Statesboro |
135
As of 2026 · Source |
Permits & Setbacks in Brantley County
Barn placement is something to figure out before the ground is cleared. If you're planning a horse barn in Fendig, contact Brantley County Planning & Building Department about the local requirements. The permit rule applies once the building exceeds Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256). square feet, and the current setback is Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.. You should also check whether any additional rules apply to keeping horses on the property before committing to a building location.
Delivery to Fendig
Your delivery estimate gives you a timeline for getting the rest of the barn project organized. Current delivery to Fendig is estimated at 1 to 2 weeks. Benton also serves nearby communities including Hortense, O Neal, Needmore and Popwellville. Check the delivery arrangements for your order and make sure the property is accessible when materials are due.
Representative product photo — a Brantley County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I store hay and feed inside my horse barn?
You can plan storage areas for feed and supplies, but hay storage deserves special attention because of fire risk, moisture and dust. Many barn designs separate bulk hay from horse housing. Think about how feed will be delivered, kept dry and accessed every day. Review the storage arrangement with a qualified equine facility professional before construction.
How wide should the aisle in a horse barn be?
The aisle needs enough room for horses and handlers to move without crowding doors, corners or stored equipment. Think about how horses will enter and leave stalls, whether you'll move wheelbarrows through the barn and how daily cleaning will work. Have the layout reviewed for safe horse handling rather than choosing an aisle width based only on available space.
Do I need a permit for a horse barn in Fendig?
The requirements for Fendig are handled by Brantley County Planning & Building Department. Currently, a permit is required once the barn exceeds Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256). square feet. Agricultural use doesn't automatically mean a building is exempt from every local rule. Check zoning, setbacks and any other requirements for your property before beginning site work or committing to the barn's location.
How many colors are available for a horse barn?
Benton's applicable horse barn materials are available in 7 colors. You may want the barn to match existing buildings, or you may prefer a traditional farm-building appearance. Color is worth choosing early, especially if the roof and walls will have different finishes. Confirm the available combinations before finalizing the material order.
How close can I build a horse barn to my property line?
The current setback in Fendig is Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts., subject to the requirements of Brantley County Planning & Building Department and your property. There may also be separate rules affecting livestock buildings or where animals can be kept. Check those requirements before marking the barn location, particularly if neighboring homes or property boundaries are nearby.
What size should horse stalls be?
Stall size depends on the horse, including its height, build and how comfortably it can turn around and lie down. A layout suitable for one horse may not work for a larger animal or a mare with a foal. Have an experienced equine facility designer or qualified professional review the stall dimensions before construction.
Is a metal horse barn too hot for Georgia summers?
A metal roof or wall system doesn't determine barn comfort by itself. Ventilation, insulation where appropriate, shade and the overall building design all affect interior conditions. In Fendig, plan for the region's warm, humid weather. Horses need adequate airflow and access to fresh water, so those requirements should be part of the design from the beginning.
Can I add a tack room and wash area to my horse barn?
Yes, those spaces can be included in the overall barn plan when the layout and building dimensions allow. A tack room needs practical storage, while a wash area needs suitable drainage and water access. Decide where both belong before choosing the final building size, since they can take up space you might otherwise assign to stalls or aisles.
Definitions
- ◦ Condensation
- Moisture that forms when humid air contacts a sufficiently cool surface. Poorly managed condensation can cause damp conditions inside a barn.
- ◦ Wash Stall
- An area designed for washing or grooming horses, with suitable water access, drainage and slip-resistant footing.
- ◦ Horse Stall
- An individual enclosed space inside a barn where a horse can rest, eat and be housed.
- ◦ Center Aisle
- A passageway running through the barn, usually with stalls or other rooms along one or both sides.
- ◦ Dutch Door
- A door divided into upper and lower sections that can open separately. Some horse barns use them for stall or exterior access.
- ◦ Ridge Vent
- A ventilation opening near the roof peak that allows warm, moist air to escape when designed as part of a functioning ventilation system.
- ◦ Roof Pitch
- The slope of the barn roof, usually described by how much it rises over a set horizontal distance.
- ◦ Setback
- The required distance between a barn and a property boundary, road or another feature covered by local building or zoning rules.
- ◦ Feed Room
- A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
- ◦ Post-Frame Construction
- A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
Fendig, Brantley County — At a Glance
- Permit Authority Name
- Brantley County Planning & Building Department
- Permit Authority Url
- https://brantleycounty-ga.gov/planning--building
- Permit Threshold Sqft
- Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256).
- Setback Feet Side Rear
- Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.
- Wind Load Zone
- Inland/near-coastal Georgia (Nahunta) — roughly 115-125 mph (ASCE 7, Exposure C); Brantley County sits just inland of the coastal GA counties (Camden/Glynn) so its mapped speed is likely somewhat lower than the ~130 mph coastal band but higher than deep-interior GA. NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 90.3
- Drive Minutes
- 135
- Nearby Towns
- Hortense, O Neal, Needmore, Popwellville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has manufactured metal building products in Statesboro since 2004 and supplies materials for agricultural projects throughout the region. For someone planning a horse barn in Fendig, that means working with a regional supplier familiar with metal roofing, siding and the materials used on farm buildings. The barn's design and animal-housing requirements should be worked out alongside the material specifications.
Ready to talk through your horse barns project in Fendig?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for horse barns specifically. (2026)
- https://brantleycounty-ga.gov/planning--building (2026)
- Land Use Ordinance for Brantley County, Georgia (adopted 9/8/2016), https://www.sgrc.us/documents/localgovernmentservices/development/4ad60d41e5b8542a349de9376b720273.pdf — needs direct lookup of the district table (2026)
- General ASCE 7 range inferred from proximity to coastal Georgia counties (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Given/client spec — Brantley County is inland Georgia (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
