Reviewed by the Benton Metal Depot team · Updated
If you're building a horse barn in Fancy Hall, don't plan around stalls alone. You'll also need to think about airflow, water access, feed, tack and where the horses will enter and leave. Benton Metal Depot supplies metal building materials throughout Bryan, with 7 exterior colors available for applicable packages.
Key Points
- ◦Plan stall dimensions around the horses that will actually use them.
- ◦Horse barn exterior materials are available in 7 colors.
- ◦Benton Metal Depot is approximately 59.8 miles from Fancy Hall.
- ◦The current local setback for a horse barn in Fancy Hall is Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF..
- ◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels
As of 2026 · Source |
| Drive time from Statesboro |
78
As of 2026 · Source |
Permits & Setbacks in Bryan County
Barn placement is something to figure out before the ground is cleared. If you're planning a horse barn in Fancy Hall, contact Bryan County Community Development Department, Building and Codes Division about the local requirements. The permit rule applies once the building exceeds 200 square feet, and the current setback is Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.. You should also check whether any additional rules apply to keeping horses on the property before committing to a building location.
Delivery to Fancy Hall
Your delivery estimate gives you a timeline for getting the rest of the barn project organized. Current delivery to Fancy Hall is estimated at 1 to 2 weeks. Benton also serves nearby communities including Daniel, Belfast, Fort McAllister and Oak Level. Check the delivery arrangements for your order and make sure the property is accessible when materials are due.
Representative product photo — a Bryan County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How wide should the aisle in a horse barn be?
The aisle needs enough room for horses and handlers to move without crowding doors, corners or stored equipment. Think about how horses will enter and leave stalls, whether you'll move wheelbarrows through the barn and how daily cleaning will work. Have the layout reviewed for safe horse handling rather than choosing an aisle width based only on available space.
Can I store hay and feed inside my horse barn?
You can plan storage areas for feed and supplies, but hay storage deserves special attention because of fire risk, moisture and dust. Many barn designs separate bulk hay from horse housing. Think about how feed will be delivered, kept dry and accessed every day. Review the storage arrangement with a qualified equine facility professional before construction.
How long does it take to get horse barn materials delivered?
Current delivery to Fancy Hall is estimated at 1 to 2 weeks. Use that window to work through permits, contractor schedules and site preparation. Confirm the estimate for your specific order when placing it and planning the overall construction schedule.
What kind of metal panels does Benton use for horse barns?
The applicable horse barn package uses 29-gauge and 26-gauge Rib panels panels. Metal roofing and siding help enclose the building and protect it from the weather, but panel selection is only part of planning a barn. Ventilation, condensation control and the safety of surfaces horses can reach should also be addressed in the finished design.
How big should a horse barn be?
Start with the number and size of your horses, then add the space needed for safe handling and daily care. Stalls are only one part of the layout. You'll also need room for aisles, doors, feed, tack and possibly a wash area. If you expect to add horses later, think about that before choosing the building dimensions.
Can I add a tack room and wash area to my horse barn?
Yes, those spaces can be included in the overall barn plan when the layout and building dimensions allow. A tack room needs practical storage, while a wash area needs suitable drainage and water access. Decide where both belong before choosing the final building size, since they can take up space you might otherwise assign to stalls or aisles.
Is a metal horse barn too hot for Georgia summers?
A metal roof or wall system doesn't determine barn comfort by itself. Ventilation, insulation where appropriate, shade and the overall building design all affect interior conditions. In Fancy Hall, plan for the region's warm, humid weather. Horses need adequate airflow and access to fresh water, so those requirements should be part of the design from the beginning.
What kind of floor is best for a horse barn?
Different parts of the barn may need different flooring. Stalls, aisles, wash areas and storage rooms don't necessarily work best with the same surface. Drainage, footing, cleaning and slip resistance should guide the decision. Plan the floor system with someone familiar with horse facilities before installing concrete or other permanent surfaces.
Definitions
- ◦ Panel Gauge
- A measurement related to sheet-metal thickness.
- ◦ Lead Time
- The period needed to process and prepare the building materials after the relevant order stage.
- ◦ Feed Room
- A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
- ◦ Post-Frame Construction
- A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
- ◦ Eave Height
- The height of the barn's exterior wall where it meets the lower edge of the roof.
- ◦ Tack Room
- A dedicated area for storing saddles, bridles, grooming supplies and other horse equipment.
- ◦ Stall Partition
- A wall or divider separating one horse stall from another or from an adjacent area.
- ◦ Setback
- The required distance between a barn and a property boundary, road or another feature covered by local building or zoning rules.
- ◦ Roof Pitch
- The slope of the barn roof, usually described by how much it rises over a set horizontal distance.
- ◦ Ridge Vent
- A ventilation opening near the roof peak that allows warm, moist air to escape when designed as part of a functioning ventilation system.
Fancy Hall, Bryan County — At a Glance
- Permit Authority Name
- Bryan County Community Development Department, Building and Codes Division
- Permit Authority Url
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
- Wind Load Zone
- Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 59.8
- Drive Minutes
- 78
- Nearby Towns
- Daniel, Belfast, Fort McAllister, Oak Level
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels
- Color Count
- 7
Why Benton Metal Depot
A horse barn involves more planning than choosing a roof and four walls. You have to think about the animals, the people caring for them and how the building will be used every day. Benton Metal Depot supplies metal panels, trim and related building materials for agricultural projects, allowing customers to coordinate those exterior materials with the rest of their barn plans.
Ready to talk through your horse barns project in Fancy Hall?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for horse barns specifically. (2026)
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes (2026)
- https://www.bryancountyga.gov/government/departments-a-g/community-development/building-and-codes/learn-more ("buildings greater than 200 square feet in size" require a building permit) (2026)
- Bryan County Code of Ordinances Ch. 114, Sec. 114-611, as summarized at https://www.zoneomics.com/code/bryan-county-unincorporated-GA/chapter_6 — verify against primary ordinance at https://library.municode.com/ga/bryan_county (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (primary: lists Bryan among the 6 GA Wind Zone 2 coastal counties: Chatham, Bryan, Liberty, McIntosh, Glynn, Camden) — mph range aggregated from windload.solutions/homenation.com secondary sources (2026)
- Given/client spec — Bryan County is a coastal Georgia county; confirmed independently by its Wind Zone 2 listing at https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
