Reviewed by the Benton Metal Depot team · Updated
A good horse barn gives you shelter, storage and enough room to handle everyday chores without everything feeling crowded. Benton Metal Depot supplies agricultural building materials for properties in Williams and nearby communities, with a lead time of 1 to 2 weeks. Knowing this gives you a starting point for planning the rest of the project.
Key Points
- ◦Horse barn exterior materials are available in 7 colors.
- ◦Plan stall dimensions around the horses that will actually use them.
- ◦Benton Metal Depot is approximately 45.7 miles from Williams.
- ◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
- ◦The current local setback for a horse barn in Williams is Not retrieved — Chatham County has its own zoning ordinance with district-specific setback tables; figures were not found in available search results and need direct lookup..
At a Glance
| Permit threshold |
No explicit sqft exemption found on the county page — it lists "garages, carports... accessory buildings, storage buildings, tool sheds" as requiring permits without stating a size cutoff. Georgia's state minimum code baseline (IRC) exempts one-story detached sheds/playhouses up to 120 sq ft, but it is unconfirmed whether Chatham County enforces that exemption as-is.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Chatham County has its own zoning ordinance with district-specific setback tables; figures were not found in available search results and need direct lookup.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia (Savannah/Chatham County) — commonly cited around 130 mph (3-second gust, ASCE 7-22, Risk Category II), with barrier-island areas (Tybee, Wilmington, Skidaway Islands) potentially reaching or exceeding 140 mph. NOT verified against a primary county map — Georgia adopted the 2024 IBC/IRC (with GA amendments) effective Jan 1, 2026, referencing ASCE 7-22, and the exact mapped speed depends on precise site location and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels
As of 2026 · Source |
| Drive time from Statesboro |
59
As of 2026 · Source |
Permits & Setbacks in Chatham County
Get the permit questions answered early so they don't hold up the rest of the project. The current permit threshold for a horse barn in Williams is No explicit sqft exemption found on the county page — it lists "garages, carports... accessory buildings, storage buildings, tool sheds" as requiring permits without stating a size cutoff. Georgia's state minimum code baseline (IRC) exempts one-story detached sheds/playhouses up to 120 sq ft, but it is unconfirmed whether Chatham County enforces that exemption as-is. square feet, with a setback of Not retrieved — Chatham County has its own zoning ordinance with district-specific setback tables; figures were not found in available search results and need direct lookup.. Those requirements fall under Chatham County Building Safety & Regulatory Services. Agricultural buildings can have different rules depending on their use and location, so verify what applies to your property before pouring concrete or completing other permanent site work.
Delivery to Williams
A little planning ahead can make barn delivery much easier, especially on a working property. Horse barn material delivery to Williams currently takes approximately 1 to 2 weeks. Benton Metal Depot is approximately 45.7 miles away. Make sure delivery vehicles can reach the unloading area and that any necessary site work is handled before the materials are scheduled to arrive.
Representative product photo — a Chatham County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What kind of floor is best for a horse barn?
Different parts of the barn may need different flooring. Stalls, aisles, wash areas and storage rooms don't necessarily work best with the same surface. Drainage, footing, cleaning and slip resistance should guide the decision. Plan the floor system with someone familiar with horse facilities before installing concrete or other permanent surfaces.
How long does it take to get horse barn materials delivered?
Current delivery to Williams is estimated at 1 to 2 weeks. Use that window to work through permits, contractor schedules and site preparation. Confirm the estimate for your specific order when placing it and planning the overall construction schedule.
How big should a horse barn be?
Start with the number and size of your horses, then add the space needed for safe handling and daily care. Stalls are only one part of the layout. You'll also need room for aisles, doors, feed, tack and possibly a wash area. If you expect to add horses later, think about that before choosing the building dimensions.
What kind of metal panels does Benton use for horse barns?
The applicable horse barn package uses 29-gauge and 26-gauge Rib panels panels. Metal roofing and siding help enclose the building and protect it from the weather, but panel selection is only part of planning a barn. Ventilation, condensation control and the safety of surfaces horses can reach should also be addressed in the finished design.
Should a horse barn have insulation?
That depends on the building design, local climate and how the barn will be used. Insulation may help manage heat transfer and condensation, but it doesn't replace ventilation. In horse housing, airflow and moisture control are important. Discuss the complete roof and wall assembly with the building designer before choosing insulation materials or enclosing the interior.
How close can I build a horse barn to my property line?
The current setback in Williams is Not retrieved — Chatham County has its own zoning ordinance with district-specific setback tables; figures were not found in available search results and need direct lookup., subject to the requirements of Chatham County Building Safety & Regulatory Services and your property. There may also be separate rules affecting livestock buildings or where animals can be kept. Check those requirements before marking the barn location, particularly if neighboring homes or property boundaries are nearby.
What size should horse stalls be?
Stall size depends on the horse, including its height, build and how comfortably it can turn around and lie down. A layout suitable for one horse may not work for a larger animal or a mare with a foal. Have an experienced equine facility designer or qualified professional review the stall dimensions before construction.
How wide should the aisle in a horse barn be?
The aisle needs enough room for horses and handlers to move without crowding doors, corners or stored equipment. Think about how horses will enter and leave stalls, whether you'll move wheelbarrows through the barn and how daily cleaning will work. Have the layout reviewed for safe horse handling rather than choosing an aisle width based only on available space.
Definitions
- ◦ Stall Partition
- A wall or divider separating one horse stall from another or from an adjacent area.
- ◦ Tack Room
- A dedicated area for storing saddles, bridles, grooming supplies and other horse equipment.
- ◦ Lead Time
- The period needed to process and prepare the building materials after the relevant order stage.
- ◦ Panel Gauge
- A measurement related to sheet-metal thickness.
- ◦ Roof Pitch
- The slope of the barn roof, usually described by how much it rises over a set horizontal distance.
- ◦ Setback
- The required distance between a barn and a property boundary, road or another feature covered by local building or zoning rules.
- ◦ Eave Height
- The height of the barn's exterior wall where it meets the lower edge of the roof.
- ◦ Post-Frame Construction
- A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
- ◦ Feed Room
- A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
- ◦ Dutch Door
- A door divided into upper and lower sections that can open separately. Some horse barns use them for stall or exterior access.
Williams, Chatham County — At a Glance
- Permit Authority Name
- Chatham County Building Safety & Regulatory Services
- Permit Authority Url
- https://buildingsafety.chathamcountyga.gov/PermitsInspections/WhenPermitsRequired
- Permit Threshold Sqft
- No explicit sqft exemption found on the county page — it lists "garages, carports... accessory buildings, storage buildings, tool sheds" as requiring permits without stating a size cutoff. Georgia's state minimum code baseline (IRC) exempts one-story detached sheds/playhouses up to 120 sq ft, but it is unconfirmed whether Chatham County enforces that exemption as-is.
- Setback Feet Side Rear
- Not retrieved — Chatham County has its own zoning ordinance with district-specific setback tables; figures were not found in available search results and need direct lookup.
- Wind Load Zone
- Coastal Georgia (Savannah/Chatham County) — commonly cited around 130 mph (3-second gust, ASCE 7-22, Risk Category II), with barrier-island areas (Tybee, Wilmington, Skidaway Islands) potentially reaching or exceeding 140 mph. NOT verified against a primary county map — Georgia adopted the 2024 IBC/IRC (with GA amendments) effective Jan 1, 2026, referencing ASCE 7-22, and the exact mapped speed depends on precise site location and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- 1
- Drive Miles
- 45.7
- Drive Minutes
- 59
- Nearby Towns
- Hamer, Pooler, Savannah, Bloomingdale
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has manufactured metal building products in Statesboro since 2004 and supplies materials for agricultural projects throughout the region. For someone planning a horse barn in Williams, that means working with a regional supplier familiar with metal roofing, siding and the materials used on farm buildings. The barn's design and animal-housing requirements should be worked out alongside the material specifications.
Ready to talk through your horse barns project in Williams?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for horse barns specifically. (2026)
- https://buildingsafety.chathamcountyga.gov/PermitsInspections/WhenPermitsRequired (2026)
- https://buildingsafety.chathamcountyga.gov/PermitsInspections/WhenPermitsRequired — needs direct confirmation by phone (912-201-4300) (2026)
- https://buildingsafety.chathamcountyga.gov/ — needs direct ordinance lookup (2026)
- Aggregated from windload.solutions and similar secondary sources — no primary Chatham County wind map found (2026)
- Given/client spec — Chatham County (Savannah) is a coastal Georgia county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Chatham County
See the Chatham County hub for horse barns
