Reviewed by the Benton Metal Depot team · Updated
A good horse barn gives you shelter, storage and enough room to handle everyday chores without everything feeling crowded. Benton Metal Depot supplies agricultural building materials for properties in Fleming and nearby communities, with a lead time of 1 to 2 weeks. Knowing this gives you a starting point for planning the rest of the project.
Key Points
- ◦In Fleming, a permit from Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections) is required once the barn exceeds No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet.
- ◦Benton Metal Depot is approximately 65.4 miles from Fleming.
- ◦Current lead time for horse barn materials to Fleming is 1 to 2 weeks.
- ◦The current local setback for a horse barn in Fleming is Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF..
- ◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
At a Glance
| Permit threshold |
No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Liberty County in Wind Zone 2. Secondary sources put ASCE 7 ultimate design wind speeds for coastal GA counties like Liberty in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and distance from the coast, and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels
As of 2026 · Source |
| Drive time from Statesboro |
85
As of 2026 · Source |
Permits & Setbacks in Liberty County
Just because a property can fit a barn doesn't necessarily mean you can put it anywhere. For a horse barn in Fleming, a permit from Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections) is required once the building exceeds No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet, and the current setback is Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.. Check with that office before choosing the final location, especially if the barn will be near a property boundary, neighboring home or another building.
Delivery to Fleming
Your delivery estimate gives you a timeline for getting the rest of the barn project organized. Current delivery to Fleming is estimated at 1 to 2 weeks. Benton also serves nearby communities including Limerick, Screven Fork, Halfmoon Landing and Sunbury. Check the delivery arrangements for your order and make sure the property is accessible when materials are due.
Representative product photo — a Liberty County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What kind of floor is best for a horse barn?
Different parts of the barn may need different flooring. Stalls, aisles, wash areas and storage rooms don't necessarily work best with the same surface. Drainage, footing, cleaning and slip resistance should guide the decision. Plan the floor system with someone familiar with horse facilities before installing concrete or other permanent surfaces.
What kind of metal panels does Benton use for horse barns?
The applicable horse barn package uses 29-gauge and 26-gauge Rib panels panels. Metal roofing and siding help enclose the building and protect it from the weather, but panel selection is only part of planning a barn. Ventilation, condensation control and the safety of surfaces horses can reach should also be addressed in the finished design.
How big should a horse barn be?
Start with the number and size of your horses, then add the space needed for safe handling and daily care. Stalls are only one part of the layout. You'll also need room for aisles, doors, feed, tack and possibly a wash area. If you expect to add horses later, think about that before choosing the building dimensions.
How long does it take to get horse barn materials delivered?
Current delivery to Fleming is estimated at 1 to 2 weeks. Use that window to work through permits, contractor schedules and site preparation. Confirm the estimate for your specific order when placing it and planning the overall construction schedule.
Should a horse barn have insulation?
That depends on the building design, local climate and how the barn will be used. Insulation may help manage heat transfer and condensation, but it doesn't replace ventilation. In horse housing, airflow and moisture control are important. Discuss the complete roof and wall assembly with the building designer before choosing insulation materials or enclosing the interior.
How wide should the aisle in a horse barn be?
The aisle needs enough room for horses and handlers to move without crowding doors, corners or stored equipment. Think about how horses will enter and leave stalls, whether you'll move wheelbarrows through the barn and how daily cleaning will work. Have the layout reviewed for safe horse handling rather than choosing an aisle width based only on available space.
Can I store hay and feed inside my horse barn?
You can plan storage areas for feed and supplies, but hay storage deserves special attention because of fire risk, moisture and dust. Many barn designs separate bulk hay from horse housing. Think about how feed will be delivered, kept dry and accessed every day. Review the storage arrangement with a qualified equine facility professional before construction.
Do I need a permit for a horse barn in Fleming?
The requirements for Fleming are handled by Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections). Currently, a permit is required once the barn exceeds No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet. Agricultural use doesn't automatically mean a building is exempt from every local rule. Check zoning, setbacks and any other requirements for your property before beginning site work or committing to the barn's location.
Definitions
- ◦ Eave Height
- The height of the barn's exterior wall where it meets the lower edge of the roof.
- ◦ Feed Room
- A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
- ◦ Post-Frame Construction
- A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
- ◦ Condensation
- Moisture that forms when humid air contacts a sufficiently cool surface. Poorly managed condensation can cause damp conditions inside a barn.
- ◦ Ridge Vent
- A ventilation opening near the roof peak that allows warm, moist air to escape when designed as part of a functioning ventilation system.
- ◦ Stall Partition
- A wall or divider separating one horse stall from another or from an adjacent area.
- ◦ Tack Room
- A dedicated area for storing saddles, bridles, grooming supplies and other horse equipment.
- ◦ Wash Stall
- An area designed for washing or grooming horses, with suitable water access, drainage and slip-resistant footing.
- ◦ Horse Stall
- An individual enclosed space inside a barn where a horse can rest, eat and be housed.
- ◦ Setback
- The required distance between a barn and a property boundary, road or another feature covered by local building or zoning rules.
Fleming, Liberty County — At a Glance
- Permit Authority Name
- Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections)
- Permit Authority Url
- https://www.libertycountyga.gov/211/Building-Licensing
- Permit Threshold Sqft
- No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation.
- Setback Feet Side Rear
- Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.
- Wind Load Zone
- Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Liberty County in Wind Zone 2. Secondary sources put ASCE 7 ultimate design wind speeds for coastal GA counties like Liberty in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and distance from the coast, and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 65.4
- Drive Minutes
- 85
- Nearby Towns
- Limerick, Screven Fork, Halfmoon Landing, Sunbury
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels
- Color Count
- 7
Why Benton Metal Depot
A horse barn involves more planning than choosing a roof and four walls. You have to think about the animals, the people caring for them and how the building will be used every day. Benton Metal Depot supplies metal panels, trim and related building materials for agricultural projects, allowing customers to coordinate those exterior materials with the rest of their barn plans.
Ready to talk through your horse barns project in Fleming?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for horse barns specifically. (2026)
- https://www.libertycountyga.gov/211/Building-Licensing (2026)
- Georgia adoption of 2024 IRC with GA Amendments (statewide baseline); Liberty County UDO referenced at https://thelcpc.org/zoning/ — specific threshold not located in accessible text (2026)
- Liberty County Unified Development Ordinance (LCPC), referenced at https://thelcpc.org/zoning/ — primary PDF needs direct retrieval/verification (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (primary: lists Liberty among the 6 GA Wind Zone 2 coastal counties) — mph range aggregated from homenation.com/blog/complete-guide-to-georgia-wind-zones and windload.solutions (2026)
- Given/client spec — Liberty County is a coastal Georgia county; confirmed independently by its Wind Zone 2 listing at https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
