Reviewed by the Benton Metal Depot team · Updated
Are you planning on getting a horse barn in Mershon? A good way to start is considering the horses and how you'll care for them each day. Their stalls, feed storage, tack and a clear aisle all need room. Benton Metal Depot supplies metal building materials for agricultural projects throughout Pierce.
Key Points
- ◦The current local setback for a horse barn in Mershon is The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number..
- ◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
- ◦Aisle width should allow horses and handlers to move comfortably and safely.
- ◦Ventilation, drainage and access to fresh water should be considered during barn planning.
- ◦Plan stall dimensions around the horses that will actually use them.
At a Glance
| Permit threshold |
Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on which ASCE 7/IBC edition Pierce County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels
As of 2026 · Source |
| Drive time from Statesboro |
120
As of 2026 · Source |
Permits & Setbacks in Pierce County
Just because a property can fit a barn doesn't necessarily mean you can put it anywhere. For a horse barn in Mershon, a permit from Pierce County Planning & Codes Department is required once the building exceeds Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF. square feet, and the current setback is The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.. Check with that office before choosing the final location, especially if the barn will be near a property boundary, neighboring home or another building.
Delivery to Mershon
Don't wait until the barn materials are ready to start thinking about the site. Customers in Mershon are currently looking at 1 to 2 weeks from Statesboro. Benton Metal Depot is about 78 miles away. Use that time to coordinate contractors and prepare the area where materials will be received.
Representative product photo — a Pierce County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How long does it take to get horse barn materials delivered?
Current delivery to Mershon is estimated at 1 to 2 weeks. Use that window to work through permits, contractor schedules and site preparation. Confirm the estimate for your specific order when placing it and planning the overall construction schedule.
What kind of floor is best for a horse barn?
Different parts of the barn may need different flooring. Stalls, aisles, wash areas and storage rooms don't necessarily work best with the same surface. Drainage, footing, cleaning and slip resistance should guide the decision. Plan the floor system with someone familiar with horse facilities before installing concrete or other permanent surfaces.
Should a horse barn have insulation?
That depends on the building design, local climate and how the barn will be used. Insulation may help manage heat transfer and condensation, but it doesn't replace ventilation. In horse housing, airflow and moisture control are important. Discuss the complete roof and wall assembly with the building designer before choosing insulation materials or enclosing the interior.
How big should a horse barn be?
Start with the number and size of your horses, then add the space needed for safe handling and daily care. Stalls are only one part of the layout. You'll also need room for aisles, doors, feed, tack and possibly a wash area. If you expect to add horses later, think about that before choosing the building dimensions.
What kind of metal panels does Benton use for horse barns?
The applicable horse barn package uses 29-gauge and 26-gauge Rib panels panels. Metal roofing and siding help enclose the building and protect it from the weather, but panel selection is only part of planning a barn. Ventilation, condensation control and the safety of surfaces horses can reach should also be addressed in the finished design.
How wide should the aisle in a horse barn be?
The aisle needs enough room for horses and handlers to move without crowding doors, corners or stored equipment. Think about how horses will enter and leave stalls, whether you'll move wheelbarrows through the barn and how daily cleaning will work. Have the layout reviewed for safe horse handling rather than choosing an aisle width based only on available space.
Can I store hay and feed inside my horse barn?
You can plan storage areas for feed and supplies, but hay storage deserves special attention because of fire risk, moisture and dust. Many barn designs separate bulk hay from horse housing. Think about how feed will be delivered, kept dry and accessed every day. Review the storage arrangement with a qualified equine facility professional before construction.
How close can I build a horse barn to my property line?
The current setback in Mershon is The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number., subject to the requirements of Pierce County Planning & Codes Department and your property. There may also be separate rules affecting livestock buildings or where animals can be kept. Check those requirements before marking the barn location, particularly if neighboring homes or property boundaries are nearby.
Definitions
- ◦ Center Aisle
- A passageway running through the barn, usually with stalls or other rooms along one or both sides.
- ◦ Dutch Door
- A door divided into upper and lower sections that can open separately. Some horse barns use them for stall or exterior access.
- ◦ Ridge Vent
- A ventilation opening near the roof peak that allows warm, moist air to escape when designed as part of a functioning ventilation system.
- ◦ Condensation
- Moisture that forms when humid air contacts a sufficiently cool surface. Poorly managed condensation can cause damp conditions inside a barn.
- ◦ Wash Stall
- An area designed for washing or grooming horses, with suitable water access, drainage and slip-resistant footing.
- ◦ Horse Stall
- An individual enclosed space inside a barn where a horse can rest, eat and be housed.
- ◦ Tack Room
- A dedicated area for storing saddles, bridles, grooming supplies and other horse equipment.
- ◦ Stall Partition
- A wall or divider separating one horse stall from another or from an adjacent area.
- ◦ Lead Time
- The period needed to process and prepare the building materials after the relevant order stage.
- ◦ Panel Gauge
- A measurement related to sheet-metal thickness.
Mershon, Pierce County — At a Glance
- Permit Authority Name
- Pierce County Planning & Codes Department
- Permit Authority Url
- https://piercecountyga.gov/building-permits/
- Permit Threshold Sqft
- Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF.
- Setback Feet Side Rear
- The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.
- Wind Load Zone
- Southeast Georgia coastal plain — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on which ASCE 7/IBC edition Pierce County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 78
- Drive Minutes
- 120
- Nearby Towns
- Bristol, Coffee, Trudie, Aspinwall
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has served contractors and property owners from Statesboro since 2004. The company manufactures metal roofing products and uses a single-source coil supplier to help maintain color consistency. For customers building a horse barn in Mershon, Benton can supply applicable metal roofing and siding materials based on the project's specifications and selected finishes.
Ready to talk through your horse barns project in Mershon?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for horse barns specifically. (2026)
- https://piercecountyga.gov/contact-planning-and-codes/ (2026)
- https://piercecountyga.gov/building-permits/ (2026)
- https://piercecountyga.gov/building-permits/ and https://piercecountyga.gov/ZONING-GLAND-USE-ORDINANCE.pdf (2026)
- https://piercecountyga.gov/ZONING-GLAND-USE-ORDINANCE.pdf (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Pierce County is inland (~40-50 miles from the Atlantic) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
