Reviewed by the Benton Metal Depot team · Updated
Do you have one horse, or several of them? It's important that the barn is suitable for both the animals and the people caring for them. Benton Metal Depot serves customers in Brier Creek Landing and throughout Screven with agricultural metal building materials, including 29-gauge and 26-gauge Rib panels panels for applicable barn packages.
Key Points
- ◦Horse barn exterior materials are available in 7 colors.
- ◦Benton Metal Depot is approximately 26.3 miles from Brier Creek Landing.
- ◦Plan stall dimensions around the horses that will actually use them.
- ◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
- ◦The current local setback for a horse barn in Brier Creek Landing is Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed..
At a Glance
| Permit threshold |
Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.
As of 2026 · Source |
| Wind load zone |
Inland east-central Georgia — roughly 105-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels
As of 2026 · Source |
| Drive time from Statesboro |
35
As of 2026 · Source |
Permits & Setbacks in Screven County
Barn placement is something to figure out before the ground is cleared. If you're planning a horse barn in Brier Creek Landing, contact Screven County Planning and Zoning Department about the local requirements. The permit rule applies once the building exceeds Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number. square feet, and the current setback is Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.. You should also check whether any additional rules apply to keeping horses on the property before committing to a building location.
Delivery to Brier Creek Landing
Your delivery estimate gives you a timeline for getting the rest of the barn project organized. Current delivery to Brier Creek Landing is estimated at 1 to 2 weeks. Benton also serves nearby communities including Dover, Woodcliff, Burtons Ferry Landing and Millhaven. Check the delivery arrangements for your order and make sure the property is accessible when materials are due.
Representative product photo — a Screven County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What kind of metal panels does Benton use for horse barns?
The applicable horse barn package uses 29-gauge and 26-gauge Rib panels panels. Metal roofing and siding help enclose the building and protect it from the weather, but panel selection is only part of planning a barn. Ventilation, condensation control and the safety of surfaces horses can reach should also be addressed in the finished design.
How big should a horse barn be?
Start with the number and size of your horses, then add the space needed for safe handling and daily care. Stalls are only one part of the layout. You'll also need room for aisles, doors, feed, tack and possibly a wash area. If you expect to add horses later, think about that before choosing the building dimensions.
Should a horse barn have insulation?
That depends on the building design, local climate and how the barn will be used. Insulation may help manage heat transfer and condensation, but it doesn't replace ventilation. In horse housing, airflow and moisture control are important. Discuss the complete roof and wall assembly with the building designer before choosing insulation materials or enclosing the interior.
What kind of floor is best for a horse barn?
Different parts of the barn may need different flooring. Stalls, aisles, wash areas and storage rooms don't necessarily work best with the same surface. Drainage, footing, cleaning and slip resistance should guide the decision. Plan the floor system with someone familiar with horse facilities before installing concrete or other permanent surfaces.
How long does it take to get horse barn materials delivered?
Current delivery to Brier Creek Landing is estimated at 1 to 2 weeks. Use that window to work through permits, contractor schedules and site preparation. Confirm the estimate for your specific order when placing it and planning the overall construction schedule.
Do I need a permit for a horse barn in Brier Creek Landing?
The requirements for Brier Creek Landing are handled by Screven County Planning and Zoning Department. Currently, a permit is required once the barn exceeds Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number. square feet. Agricultural use doesn't automatically mean a building is exempt from every local rule. Check zoning, setbacks and any other requirements for your property before beginning site work or committing to the barn's location.
How many colors are available for a horse barn?
Benton's applicable horse barn materials are available in 7 colors. You may want the barn to match existing buildings, or you may prefer a traditional farm-building appearance. Color is worth choosing early, especially if the roof and walls will have different finishes. Confirm the available combinations before finalizing the material order.
Can I add a tack room and wash area to my horse barn?
Yes, those spaces can be included in the overall barn plan when the layout and building dimensions allow. A tack room needs practical storage, while a wash area needs suitable drainage and water access. Decide where both belong before choosing the final building size, since they can take up space you might otherwise assign to stalls or aisles.
Definitions
- ◦ Feed Room
- A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
- ◦ Post-Frame Construction
- A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
- ◦ Eave Height
- The height of the barn's exterior wall where it meets the lower edge of the roof.
- ◦ Ridge Vent
- A ventilation opening near the roof peak that allows warm, moist air to escape when designed as part of a functioning ventilation system.
- ◦ Condensation
- Moisture that forms when humid air contacts a sufficiently cool surface. Poorly managed condensation can cause damp conditions inside a barn.
- ◦ Tack Room
- A dedicated area for storing saddles, bridles, grooming supplies and other horse equipment.
- ◦ Stall Partition
- A wall or divider separating one horse stall from another or from an adjacent area.
- ◦ Lead Time
- The period needed to process and prepare the building materials after the relevant order stage.
- ◦ Panel Gauge
- A measurement related to sheet-metal thickness.
- ◦ Wash Stall
- An area designed for washing or grooming horses, with suitable water access, drainage and slip-resistant footing.
Brier Creek Landing, Screven County — At a Glance
- Permit Authority Name
- Screven County Planning and Zoning Department
- Permit Authority Url
- https://www.screvencountyboc.com/planning-zoning
- Permit Threshold Sqft
- Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number.
- Setback Feet Side Rear
- Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.
- Wind Load Zone
- Inland east-central Georgia — roughly 105-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 26.3
- Drive Minutes
- 35
- Nearby Towns
- Dover, Woodcliff, Burtons Ferry Landing, Millhaven
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has served contractors and property owners from Statesboro since 2004. The company manufactures metal roofing products and uses a single-source coil supplier to help maintain color consistency. For customers building a horse barn in Brier Creek Landing, Benton can supply applicable metal roofing and siding materials based on the project's specifications and selected finishes.
Ready to talk through your horse barns project in Brier Creek Landing?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for horse barns specifically. (2026)
- https://www.screvencountyboc.com/planning-zoning (2026)
- https://www.zoneomics.com/code/screven-county-unincorporated-GA/chapter_13 — verify against the primary ordinance at https://library.municode.com/GA/Screven_County/codes/Code_of_Ordinances (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Screven County is well inland (east-central Georgia, on the Savannah River but far from the coast) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
