Reviewed by the Benton Metal Depot team · Updated
If you're building a horse barn in Bolen, don't plan around stalls alone. You'll also need to think about airflow, water access, feed, tack and where the horses will enter and leave. Benton Metal Depot supplies metal building materials throughout Ware, with 7 exterior colors available for applicable packages.
Key Points
- ◦In Bolen, a permit from Ware County Planning & Codes Department is required once the barn exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet.
- ◦Benton Metal Depot is approximately 98.9 miles from Bolen.
- ◦Current lead time for horse barn materials to Bolen is 1 to 2 weeks.
- ◦Ventilation, drainage and access to fresh water should be considered during barn planning.
- ◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
At a Glance
| Permit threshold |
Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels
As of 2026 · Source |
| Drive time from Statesboro |
148
As of 2026 · Source |
Permits & Setbacks in Ware County
Just because a property can fit a barn doesn't necessarily mean you can put it anywhere. For a horse barn in Bolen, a permit from Ware County Planning & Codes Department is required once the building exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet, and the current setback is Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.. Check with that office before choosing the final location, especially if the barn will be near a property boundary, neighboring home or another building.
Delivery to Bolen
Your delivery estimate gives you a timeline for getting the rest of the barn project organized. Current delivery to Bolen is estimated at 1 to 2 weeks. Benton also serves nearby communities including Waresboro, Dixie Union, Skullhead and Sappville. Check the delivery arrangements for your order and make sure the property is accessible when materials are due.
Representative product photo — a Ware County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should a horse barn have insulation?
That depends on the building design, local climate and how the barn will be used. Insulation may help manage heat transfer and condensation, but it doesn't replace ventilation. In horse housing, airflow and moisture control are important. Discuss the complete roof and wall assembly with the building designer before choosing insulation materials or enclosing the interior.
How many colors are available for a horse barn?
Benton's applicable horse barn materials are available in 7 colors. You may want the barn to match existing buildings, or you may prefer a traditional farm-building appearance. Color is worth choosing early, especially if the roof and walls will have different finishes. Confirm the available combinations before finalizing the material order.
Do I need a permit for a horse barn in Bolen?
The requirements for Bolen are handled by Ware County Planning & Codes Department. Currently, a permit is required once the barn exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet. Agricultural use doesn't automatically mean a building is exempt from every local rule. Check zoning, setbacks and any other requirements for your property before beginning site work or committing to the barn's location.
What size should horse stalls be?
Stall size depends on the horse, including its height, build and how comfortably it can turn around and lie down. A layout suitable for one horse may not work for a larger animal or a mare with a foal. Have an experienced equine facility designer or qualified professional review the stall dimensions before construction.
How close can I build a horse barn to my property line?
The current setback in Bolen is Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes., subject to the requirements of Ware County Planning & Codes Department and your property. There may also be separate rules affecting livestock buildings or where animals can be kept. Check those requirements before marking the barn location, particularly if neighboring homes or property boundaries are nearby.
What kind of floor is best for a horse barn?
Different parts of the barn may need different flooring. Stalls, aisles, wash areas and storage rooms don't necessarily work best with the same surface. Drainage, footing, cleaning and slip resistance should guide the decision. Plan the floor system with someone familiar with horse facilities before installing concrete or other permanent surfaces.
Can I add a tack room and wash area to my horse barn?
Yes, those spaces can be included in the overall barn plan when the layout and building dimensions allow. A tack room needs practical storage, while a wash area needs suitable drainage and water access. Decide where both belong before choosing the final building size, since they can take up space you might otherwise assign to stalls or aisles.
Is a metal horse barn too hot for Georgia summers?
A metal roof or wall system doesn't determine barn comfort by itself. Ventilation, insulation where appropriate, shade and the overall building design all affect interior conditions. In Bolen, plan for the region's warm, humid weather. Horses need adequate airflow and access to fresh water, so those requirements should be part of the design from the beginning.
Definitions
- ◦ Roof Pitch
- The slope of the barn roof, usually described by how much it rises over a set horizontal distance.
- ◦ Setback
- The required distance between a barn and a property boundary, road or another feature covered by local building or zoning rules.
- ◦ Wash Stall
- An area designed for washing or grooming horses, with suitable water access, drainage and slip-resistant footing.
- ◦ Horse Stall
- An individual enclosed space inside a barn where a horse can rest, eat and be housed.
- ◦ Lead Time
- The period needed to process and prepare the building materials after the relevant order stage.
- ◦ Panel Gauge
- A measurement related to sheet-metal thickness.
- ◦ Center Aisle
- A passageway running through the barn, usually with stalls or other rooms along one or both sides.
- ◦ Dutch Door
- A door divided into upper and lower sections that can open separately. Some horse barns use them for stall or exterior access.
- ◦ Feed Room
- A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
- ◦ Post-Frame Construction
- A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
Bolen, Ware County — At a Glance
- Permit Authority Name
- Ware County Planning & Codes Department
- Permit Authority Url
- https://www.warecountyga.gov/department-nodes/planning-codes
- Permit Threshold Sqft
- Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
- Setback Feet Side Rear
- Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
- Wind Load Zone
- Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 98.9
- Drive Minutes
- 148
- Nearby Towns
- Waresboro, Dixie Union, Skullhead, Sappville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels
- Color Count
- 7
Why Benton Metal Depot
A horse barn involves more planning than choosing a roof and four walls. You have to think about the animals, the people caring for them and how the building will be used every day. Benton Metal Depot supplies metal panels, trim and related building materials for agricultural projects, allowing customers to coordinate those exterior materials with the rest of their barn plans.
Ready to talk through your horse barns project in Bolen?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for horse barns specifically. (2026)
- https://www.warecountyga.gov/department-nodes/planning-codes (2026)
- https://cdn.prod.website-files.com/63d5ca60103cc0d24935804f/6a04892b6f4197158d50f3ea_2026-05-WARE-COUNTY-ZONING-ORDINANCE-ARTICLES-3-THRU-12.pdf (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Ware County is inland (Waycross area) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
