Reviewed by the Benton Metal Depot team · Updated
Do you have one horse, or several of them? It's important that the barn is suitable for both the animals and the people caring for them. Benton Metal Depot serves customers in Fripp Landing and throughout Beaufort with agricultural metal building materials, including 29-gauge and 26-gauge Rib panels panels for applicable barn packages.
Key Points
- ◦In Fripp Landing, a permit from Beaufort County Community Development Department, Building Codes / Inspections Division is required once the barn exceeds 200 square feet.
- ◦Benton Metal Depot is approximately 81.8 miles from Fripp Landing.
- ◦Current lead time for horse barn materials to Fripp Landing is 1 to 2 weeks.
- ◦The current local setback for a horse barn in Fripp Landing is For accessory structures 16 ft or less in height: 5 ft from both side and rear property lines. For structures over 16 ft in height, the zoning district's general dimensional standards in the Land Development Ordinance apply instead — those district-specific figures were not independently pulled..
- ◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
For accessory structures 16 ft or less in height: 5 ft from both side and rear property lines. For structures over 16 ft in height, the zoning district's general dimensional standards in the Land Development Ordinance apply instead — those district-specific figures were not independently pulled.
As of 2026 · Source |
| Wind load zone |
Coastal South Carolina Wind Zone 3 / Coastal High-Hazard area — secondary sources put design wind speeds at roughly 130-150 mph, with 150 mph (or 140 mph within one mile of the coastline) commonly cited for SC Wind Zone 3. Exact figure for a specific parcel depends on distance from the coast, ASCE 7 edition, exposure, and risk category, and must be confirmed with an SC-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels
As of 2026 · Source |
| Drive time from Statesboro |
103
As of 2026 · Source |
Permits & Setbacks in Beaufort County
Check the building rules before you settle on a location for the barn. Horse barn permit requirements in Fripp Landing are handled by Beaufort County Community Development Department, Building Codes / Inspections Division. The current threshold is 200 square feet, but building size may not be the only consideration. Zoning, setbacks and how the property will be used can also affect the project. Confirm those details before preparing the site or beginning permanent construction work.
Delivery to Fripp Landing
Once you know what barn you need, the next step is getting the property ready for it. The typical lead time for a horse barn package to Fripp Landing is 1 to 2 weeks. Use that window to handle permits, access and any site preparation. If you're arranging grading or concrete work, coordinate those jobs with the building specifications and expected delivery schedule.
Representative product photo — a Beaufort County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How close can I build a horse barn to my property line?
The current setback in Fripp Landing is For accessory structures 16 ft or less in height: 5 ft from both side and rear property lines. For structures over 16 ft in height, the zoning district's general dimensional standards in the Land Development Ordinance apply instead — those district-specific figures were not independently pulled., subject to the requirements of Beaufort County Community Development Department, Building Codes / Inspections Division and your property. There may also be separate rules affecting livestock buildings or where animals can be kept. Check those requirements before marking the barn location, particularly if neighboring homes or property boundaries are nearby.
What kind of floor is best for a horse barn?
Different parts of the barn may need different flooring. Stalls, aisles, wash areas and storage rooms don't necessarily work best with the same surface. Drainage, footing, cleaning and slip resistance should guide the decision. Plan the floor system with someone familiar with horse facilities before installing concrete or other permanent surfaces.
What size should horse stalls be?
Stall size depends on the horse, including its height, build and how comfortably it can turn around and lie down. A layout suitable for one horse may not work for a larger animal or a mare with a foal. Have an experienced equine facility designer or qualified professional review the stall dimensions before construction.
Should a horse barn have insulation?
That depends on the building design, local climate and how the barn will be used. Insulation may help manage heat transfer and condensation, but it doesn't replace ventilation. In horse housing, airflow and moisture control are important. Discuss the complete roof and wall assembly with the building designer before choosing insulation materials or enclosing the interior.
Do I need a permit for a horse barn in Fripp Landing?
The requirements for Fripp Landing are handled by Beaufort County Community Development Department, Building Codes / Inspections Division. Currently, a permit is required once the barn exceeds 200 square feet. Agricultural use doesn't automatically mean a building is exempt from every local rule. Check zoning, setbacks and any other requirements for your property before beginning site work or committing to the barn's location.
How many colors are available for a horse barn?
Benton's applicable horse barn materials are available in 7 colors. You may want the barn to match existing buildings, or you may prefer a traditional farm-building appearance. Color is worth choosing early, especially if the roof and walls will have different finishes. Confirm the available combinations before finalizing the material order.
Can I store hay and feed inside my horse barn?
You can plan storage areas for feed and supplies, but hay storage deserves special attention because of fire risk, moisture and dust. Many barn designs separate bulk hay from horse housing. Think about how feed will be delivered, kept dry and accessed every day. Review the storage arrangement with a qualified equine facility professional before construction.
How wide should the aisle in a horse barn be?
The aisle needs enough room for horses and handlers to move without crowding doors, corners or stored equipment. Think about how horses will enter and leave stalls, whether you'll move wheelbarrows through the barn and how daily cleaning will work. Have the layout reviewed for safe horse handling rather than choosing an aisle width based only on available space.
Definitions
- ◦ Stall Partition
- A wall or divider separating one horse stall from another or from an adjacent area.
- ◦ Tack Room
- A dedicated area for storing saddles, bridles, grooming supplies and other horse equipment.
- ◦ Roof Pitch
- The slope of the barn roof, usually described by how much it rises over a set horizontal distance.
- ◦ Setback
- The required distance between a barn and a property boundary, road or another feature covered by local building or zoning rules.
- ◦ Lead Time
- The period needed to process and prepare the building materials after the relevant order stage.
- ◦ Panel Gauge
- A measurement related to sheet-metal thickness.
- ◦ Eave Height
- The height of the barn's exterior wall where it meets the lower edge of the roof.
- ◦ Post-Frame Construction
- A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
- ◦ Feed Room
- A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
- ◦ Condensation
- Moisture that forms when humid air contacts a sufficiently cool surface. Poorly managed condensation can cause damp conditions inside a barn.
Fripp Landing, Beaufort County — At a Glance
- Permit Authority Name
- Beaufort County Community Development Department, Building Codes / Inspections Division
- Permit Authority Url
- https://www.beaufortcountysc.gov/building-codes/requirements.html
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- For accessory structures 16 ft or less in height: 5 ft from both side and rear property lines. For structures over 16 ft in height, the zoning district's general dimensional standards in the Land Development Ordinance apply instead — those district-specific figures were not independently pulled.
- Wind Load Zone
- Coastal South Carolina Wind Zone 3 / Coastal High-Hazard area — secondary sources put design wind speeds at roughly 130-150 mph, with 150 mph (or 140 mph within one mile of the coastline) commonly cited for SC Wind Zone 3. Exact figure for a specific parcel depends on distance from the coast, ASCE 7 edition, exposure, and risk category, and must be confirmed with an SC-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 81.8
- Drive Minutes
- 103
- Nearby Towns
- Baileys Landing, Pinckney Colony, Brighton Beach, Palmetto Bluff
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels
- Color Count
- 7
Why Benton Metal Depot
A horse barn involves more planning than choosing a roof and four walls. You have to think about the animals, the people caring for them and how the building will be used every day. Benton Metal Depot supplies metal panels, trim and related building materials for agricultural projects, allowing customers to coordinate those exterior materials with the rest of their barn plans.
Ready to talk through your horse barns project in Fripp Landing?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for horse barns specifically. (2026)
- https://www.beaufortcountysc.gov/building-codes/index.html (2026)
- https://www.beaufortcountysc.gov/building-codes/requirements.html (2026)
- https://www.beaufortcountysc.gov/code-enforcement/faq.html ("Accessory structures 200 square feet and larger require a Building Permit... including pre-built structures"; a Zoning Permit is also required before placing any accessory structure) (2026)
- https://www.beaufortcountysc.gov/code-enforcement/faq.html — cross-reference against primary Beaufort County Land Development Code, Art. 4 Div. 4.2 "Accessory Uses and Structures" at https://library.municode.com/sc/beaufort_county (2026)
- Aggregated from windload.solutions/south-carolina-wind-load-requirements and scbaldwin.com/blog/coastal-building-codes-wind-salt-air-sc — no Beaufort County-specific primary wind-speed map/ordinance page was located; needs verification (2026)
- Given/client spec — Beaufort County is a coastal South Carolina county (Atlantic coastline, Sea Islands) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Beaufort County
See the Beaufort County hub for horse barns
