Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Oberry can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Atkinson and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦In Oberry, a building permit is required once the garage exceeds No explicit sqft exemption found published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Atkinson County specifically. Needs direct county contact. square feet.
- ◦Benton serves Bridgetown, Mora, Willacoochee and Gladys and other communities around Oberry.
- ◦The current local setback for a metal garage is Not found — no Atkinson County zoning ordinance or accessory-structure setback table was locatable online. Needs direct confirmation with the county (912-422-3391)..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
No explicit sqft exemption found published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Atkinson County specifically. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no Atkinson County zoning ordinance or accessory-structure setback table was locatable online. Needs direct confirmation with the county (912-422-3391).
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
186
As of 2026 · Source |
Permits & Setbacks in Atkinson County
The permit question for a Oberry metal garage comes down to one number from Atkinson County Public Works and Planning Department: No explicit sqft exemption found published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Atkinson County specifically. Needs direct county contact. square feet. Stay under it and skip the full permit process; either way, keep the Not found — no Atkinson County zoning ordinance or accessory-structure setback table was locatable online. Needs direct confirmation with the county (912-422-3391). setback in mind before you pick a spot.
Delivery to Oberry
Residents in Oberry are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 136 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Atkinson County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Atkinson County Public Works and Planning Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Oberry, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Oberry?
That depends on the garage and the requirements of Atkinson County Public Works and Planning Department. The current rule requires a permit once the garage exceeds No explicit sqft exemption found published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Atkinson County specifically. Needs direct county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
How long does it take to get a metal garage delivered to Oberry?
Current delivery time to Oberry is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Atkinson County Public Works and Planning Department has requirements that can affect garage placement, including a current setback of Not found — no Atkinson County zoning ordinance or accessory-structure setback table was locatable online. Needs direct confirmation with the county (912-422-3391).. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
Oberry, Atkinson County — At a Glance
- Permit Authority Name
- Atkinson County Public Works and Planning Department
- Permit Authority Url
- https://atkinsoncounty.org/forms-and-applications/
- Permit Threshold Sqft
- No explicit sqft exemption found published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft absent a stricter local amendment — not confirmed for Atkinson County specifically. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no Atkinson County zoning ordinance or accessory-structure setback table was locatable online. Needs direct confirmation with the county (912-422-3391).
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 136
- Drive Minutes
- 186
- Nearby Towns
- Bridgetown, Mora, Willacoochee, Gladys
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Oberry and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Oberry?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://atkinsoncounty.org/forms-and-applications/ (2026)
- Georgia adoption of 2024 IRC with GA Amendments (statewide baseline); no Atkinson County-specific threshold located online (2026)
- No primary or secondary source located for Atkinson County setbacks (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Atkinson County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Atkinson County (Pearson, GA) is deep inland South Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
