Reviewed by the Benton Metal Depot team · Updated
For some residents in Girard, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Burke, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Benton serves Hills Store, Rock Fence Crossroads, Murray Hill and Sardis and other communities around Girard.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦In Girard, a building permit is required once the garage exceeds 200 square feet.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
CAUTION: an earlier search synthesis returned a "15 ft from property lines, 80 ft front setback on vacant parcels" figure, but that mixed in material from Burke County, North Carolina (burkenc.org), an unrelated jurisdiction — NOT used here as a confirmed Burke County, GA fact. The real setback figures should be pulled directly from Burke County, GA's own ordinance (Code of Ordinances Ch. 26, Art. IV) before publishing.
As of 2026 · Source |
| Wind load zone |
Inland east Georgia (Burke County borders the Savannah River near Augusta) — roughly 105-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
65
As of 2026 · Source |
Permits & Setbacks in Burke County
Burke's permitting office, Burke County Planning Department (Permits and Inspections Division), sets the accessory-structure line at 200 square feet — build under that and you generally skip the full building-permit process, though a setback of CAUTION: an earlier search synthesis returned a "15 ft from property lines, 80 ft front setback on vacant parcels" figure, but that mixed in material from Burke County, North Carolina (burkenc.org), an unrelated jurisdiction — NOT used here as a confirmed Burke County, GA fact. The real setback figures should be pulled directly from Burke County, GA's own ordinance (Code of Ordinances Ch. 26, Art. IV) before publishing. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Girard
Residents in Girard are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 49.4 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Burke County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Girard, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Burke County Planning Department (Permits and Inspections Division). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Do I need a permit for a metal garage in Girard?
That depends on the garage and the requirements of Burke County Planning Department (Permits and Inspections Division). The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
How long does it take to get a metal garage delivered to Girard?
Current delivery time to Girard is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Girard, Burke County — At a Glance
- Permit Authority Name
- Burke County Planning Department (Permits and Inspections Division)
- Permit Authority Url
- https://burkecounty-ga.gov/departments/planning_department/permits_and_inspections.php
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- CAUTION: an earlier search synthesis returned a "15 ft from property lines, 80 ft front setback on vacant parcels" figure, but that mixed in material from Burke County, North Carolina (burkenc.org), an unrelated jurisdiction — NOT used here as a confirmed Burke County, GA fact. The real setback figures should be pulled directly from Burke County, GA's own ordinance (Code of Ordinances Ch. 26, Art. IV) before publishing.
- Wind Load Zone
- Inland east Georgia (Burke County borders the Savannah River near Augusta) — roughly 105-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 49.4
- Drive Minutes
- 65
- Nearby Towns
- Hills Store, Rock Fence Crossroads, Murray Hill, Sardis
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Girard and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Girard?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://burkecounty-ga.gov/departments/planning_department/permits_and_inspections.php (2026)
- https://burkecounty-ga.gov/departments/planning_department/permits_and_inspections.php ("accessory storage buildings less than 200 square feet may be exempt from a building permit but building setbacks shall still be considered"); the same page also references a general ~$1,500 construction-value threshold for permits — confirm how the two thresholds interact (2026)
- https://library.municode.com/ga/burke_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH26LADECO_ARTIVSIDEST (not independently re-extractable as text in this pass — needs direct manual review) (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Burke County is well inland (east Georgia, near Augusta) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
