Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Olifftown? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Candler, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 19.5 miles from Olifftown.
- ◦Delivery to Olifftown is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦In Olifftown, a building permit is required once the garage exceeds 100 square feet.
At a Glance
| Permit threshold |
100
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Referenced but not confirmed — the county page cites "Section 802.5" of the Candler County Zoning Ordinance for setbacks, but the specific distances could not be extracted from the ordinance PDF in this research pass. Needs direct confirmation with the Zoning Administrator (912-685-2835).
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Candler County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
34
As of 2026 · Source |
Permits & Setbacks in Candler County
Before a metal garage goes up in Olifftown, check with Candler County Zoning Administrator (building permit applications go through this office; a separate Assessor's Office handles mobile home/electrical permits) — Candler's cutoff for requiring a building permit is 100 square feet. Below that, you still need to clear the Referenced but not confirmed — the county page cites "Section 802.5" of the Candler County Zoning Ordinance for setbacks, but the specific distances could not be extracted from the ordinance PDF in this research pass. Needs direct confirmation with the Zoning Administrator (912-685-2835). setback from your property line.
Delivery to Olifftown
Metal garage delivery to Olifftown can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Candler County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Olifftown, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Olifftown?
That depends on the garage and the requirements of Candler County Zoning Administrator (building permit applications go through this office; a separate Assessor's Office handles mobile home/electrical permits). The current rule requires a permit once the garage exceeds 100 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Candler County Zoning Administrator (building permit applications go through this office; a separate Assessor's Office handles mobile home/electrical permits). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
How long does it take to get a metal garage delivered to Olifftown?
Current delivery time to Olifftown is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Definitions
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
Olifftown, Candler County — At a Glance
- Permit Authority Name
- Candler County Zoning Administrator (building permit applications go through this office; a separate Assessor's Office handles mobile home/electrical permits)
- Permit Authority Url
- https://candlerco-ga.gov/1228/Building-Permits
- Permit Threshold Sqft
- 100
- Setback Feet Side Rear
- Referenced but not confirmed — the county page cites "Section 802.5" of the Candler County Zoning Ordinance for setbacks, but the specific distances could not be extracted from the ordinance PDF in this research pass. Needs direct confirmation with the Zoning Administrator (912-685-2835).
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Candler County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 19.5
- Drive Minutes
- 34
- Nearby Towns
- Aline, Parish, Pulaski, Metter
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Olifftown, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Olifftown?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://candlerco-ga.gov/1228/Building-Permits (2026)
- https://candlerco-ga.gov/1228/Building-Permits — "A building permit is required under the zoning ordinance...for the construction or addition of square footage greater than 10' X 10' [100 sq ft]" (Section 802.4, Candler County Zoning Ordinance). Verify against the primary ordinance PDF at https://metter-candlercounty.com/index_238_2282343757.pdf, which could not be parsed via automated fetch in this research pass. (2026)
- https://metter-candlercounty.com/index_238_2282343757.pdf (Candler County Zoning Ordinance, Section 802.5) (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Candler County is inland (southeast-central GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
