Reviewed by the Benton Metal Depot team · Updated
For some residents in Mora, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Coffee, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 136 miles from Mora.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Mora is currently estimated at 1 to 2 weeks.
At a Glance
| Permit threshold |
Not explicitly published — Code Enforcement confirms it writes permits for "new construction...swimming pool, utility shed" among other categories, implying sheds do require permits, but no specific sqft exemption threshold was found online. Needs direct confirmation (912-393-7170/7171).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed — Coffee County's zoning districts and dimensional standards are published via Municode (Appendix D, Chapter 3 – Zoning Districts) but specific setback figures were not extractable via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Coffee County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
186
As of 2026 · Source |
Permits & Setbacks in Coffee County
Before a metal garage goes up in Mora, check with Coffee County Code Enforcement Department — Coffee's cutoff for requiring a building permit is Not explicitly published — Code Enforcement confirms it writes permits for "new construction...swimming pool, utility shed" among other categories, implying sheds do require permits, but no specific sqft exemption threshold was found online. Needs direct confirmation (912-393-7170/7171). square feet. Below that, you still need to clear the Not confirmed — Coffee County's zoning districts and dimensional standards are published via Municode (Appendix D, Chapter 3 – Zoning Districts) but specific setback figures were not extractable via search. Needs direct confirmation. setback from your property line.
Delivery to Mora
Current delivery time to Mora is approximately 1 to 2 weeks. Benton also serves nearby communities including Bridgetown, Oberry, Willacoochee and Gladys. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Coffee County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Mora, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Mora before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Mora?
Current delivery time to Mora is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How far is Benton Metal Depot from Mora?
Benton Metal Depot's Statesboro location is approximately 136 miles from Mora. The company serves residents throughout Coffee, including communities such as Bridgetown, Oberry, Willacoochee and Gladys. Current delivery time for a metal garage to the Mora area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Mora is Not confirmed — Coffee County's zoning districts and dimensional standards are published via Municode (Appendix D, Chapter 3 – Zoning Districts) but specific setback figures were not extractable via search. Needs direct confirmation., although you should confirm the requirement for your particular property with Coffee County Code Enforcement Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Coffee County Code Enforcement Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
Mora, Coffee County — At a Glance
- Permit Authority Name
- Coffee County Code Enforcement Department
- Permit Authority Url
- https://www.coffeecounty-ga.gov/departments/code_enforcement/index.php
- Permit Threshold Sqft
- Not explicitly published — Code Enforcement confirms it writes permits for "new construction...swimming pool, utility shed" among other categories, implying sheds do require permits, but no specific sqft exemption threshold was found online. Needs direct confirmation (912-393-7170/7171).
- Setback Feet Side Rear
- Not confirmed — Coffee County's zoning districts and dimensional standards are published via Municode (Appendix D, Chapter 3 – Zoning Districts) but specific setback figures were not extractable via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Coffee County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 136
- Drive Minutes
- 186
- Nearby Towns
- Bridgetown, Oberry, Willacoochee, Gladys
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Mora, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Mora?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.coffeecounty-ga.gov/departments/code_enforcement/index.php (2026)
- https://library.municode.com/ga/coffee_county/codes/code_of_ordinances?nodeId=PTIICOOR_APXDLADECO_CH3ZODI (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Coffee County is inland (south-central GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
