Reviewed by the Benton Metal Depot team · Updated
For some residents in Kirkland, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Jeff Davis, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Benton Metal Depot is approximately 80.1 miles from Kirkland.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Kirkland is currently estimated at 1 to 2 weeks.
- ◦Benton serves Tallahassee, Roper, Brooker and Satilla and other communities around Kirkland.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures on the county site or in searchable secondary sources. Jeff Davis is a small rural county with limited online permitting documentation; needs a direct call to the County Commissioners' office (912-375-6611) to confirm.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no published zoning ordinance or setback table located online for Jeff Davis County. Needs direct confirmation with the county.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Jeff Davis County has adopted and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
118
As of 2026 · Source |
Permits & Setbacks in Jeff Davis County
Jeff Davis's permitting office, Jeff Davis County government (no dedicated online Building/Permitting Department page was found; permits appear to be filed through the County Commissioners' Clerk's Office), sets the accessory-structure line at Not found — no published sqft exemption for accessory structures on the county site or in searchable secondary sources. Jeff Davis is a small rural county with limited online permitting documentation; needs a direct call to the County Commissioners' office (912-375-6611) to confirm. square feet — build under that and you generally skip the full building-permit process, though a setback of Not found — no published zoning ordinance or setback table located online for Jeff Davis County. Needs direct confirmation with the county. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Kirkland
Metal garage delivery to Kirkland can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Jeff Davis County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How long does it take to get a metal garage delivered to Kirkland?
Current delivery time to Kirkland is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Kirkland before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Jeff Davis County government (no dedicated online Building/Permitting Department page was found; permits appear to be filed through the County Commissioners' Clerk's Office). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Kirkland, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How close can my metal garage be to the property line?
The current setback in Kirkland is Not found — no published zoning ordinance or setback table located online for Jeff Davis County. Needs direct confirmation with the county., although you should confirm the requirement for your particular property with Jeff Davis County government (no dedicated online Building/Permitting Department page was found; permits appear to be filed through the County Commissioners' Clerk's Office). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Kirkland?
Benton Metal Depot's Statesboro location is approximately 80.1 miles from Kirkland. The company serves residents throughout Jeff Davis, including communities such as Tallahassee, Roper, Brooker and Satilla. Current delivery time for a metal garage to the Kirkland area is about 1 to 2 weeks.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Jeff Davis County government (no dedicated online Building/Permitting Department page was found; permits appear to be filed through the County Commissioners' Clerk's Office) has requirements that can affect garage placement, including a current setback of Not found — no published zoning ordinance or setback table located online for Jeff Davis County. Needs direct confirmation with the county.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
Kirkland, Jeff Davis County — At a Glance
- Permit Authority Name
- Jeff Davis County government (no dedicated online Building/Permitting Department page was found; permits appear to be filed through the County Commissioners' Clerk's Office)
- Permit Authority Url
- https://jeffdaviscountyga.gov/
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures on the county site or in searchable secondary sources. Jeff Davis is a small rural county with limited online permitting documentation; needs a direct call to the County Commissioners' office (912-375-6611) to confirm.
- Setback Feet Side Rear
- Not found — no published zoning ordinance or setback table located online for Jeff Davis County. Needs direct confirmation with the county.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Jeff Davis County has adopted and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- Drive Miles
- 80.1
- Drive Minutes
- 118
- Nearby Towns
- Tallahassee, Roper, Brooker, Satilla
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Kirkland and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Kirkland?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://jeffdaviscountyga.gov/ — the county homepage lists no separate Building/Zoning department page as of this search (2026)
- https://jeffdaviscountyga.gov/ (2026)
- No primary source found; https://jeffdaviscountyga.gov/ has no permitting subpage (2026)
- No primary source found (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources, e.g. windload.solutions) — no county-specific or primary map source found (2026)
- Jeff Davis County is well inland (south-central GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
