Reviewed by the Benton Metal Depot team · Updated
For some residents in Teeterville, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Lanier, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦In Teeterville, a building permit is required once the garage exceeds Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation at the Tax Assessor's Office (229-482-2090). square feet.
- ◦Benton serves Lakeland, Stockton, New Lois and Ray City and other communities around Teeterville.
- ◦The current local setback for a metal garage is Not confirmed — the Lanier County Unincorporated Zoning Ordinance (Chapter 4, Land Development Districts / Chapter 6, Development Standards) likely contains a setback table, but specific figures were not extractable via search. Needs direct confirmation..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation at the Tax Assessor's Office (229-482-2090).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed — the Lanier County Unincorporated Zoning Ordinance (Chapter 4, Land Development Districts / Chapter 6, Development Standards) likely contains a setback table, but specific figures were not extractable via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Lanier County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
213
As of 2026 · Source |
Permits & Setbacks in Lanier County
Lanier's permitting office, Lanier County Planning and Zoning (construction permits are physically obtained at the Lanier County Tax Assessor's Office, coordinated with Planning & Zoning, Code Enforcement, and Inspections), sets the accessory-structure line at Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation at the Tax Assessor's Office (229-482-2090). square feet — build under that and you generally skip the full building-permit process, though a setback of Not confirmed — the Lanier County Unincorporated Zoning Ordinance (Chapter 4, Land Development Districts / Chapter 6, Development Standards) likely contains a setback table, but specific figures were not extractable via search. Needs direct confirmation. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Teeterville
Residents in Teeterville are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 156.2 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Lanier County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Teeterville?
That depends on the garage and the requirements of Lanier County Planning and Zoning (construction permits are physically obtained at the Lanier County Tax Assessor's Office, coordinated with Planning & Zoning, Code Enforcement, and Inspections). The current rule requires a permit once the garage exceeds Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation at the Tax Assessor's Office (229-482-2090). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Teeterville, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Lanier County Planning and Zoning (construction permits are physically obtained at the Lanier County Tax Assessor's Office, coordinated with Planning & Zoning, Code Enforcement, and Inspections). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
How far is Benton Metal Depot from Teeterville?
Benton Metal Depot's Statesboro location is approximately 156.2 miles from Teeterville. The company serves residents throughout Lanier, including communities such as Lakeland, Stockton, New Lois and Ray City. Current delivery time for a metal garage to the Teeterville area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Teeterville is Not confirmed — the Lanier County Unincorporated Zoning Ordinance (Chapter 4, Land Development Districts / Chapter 6, Development Standards) likely contains a setback table, but specific figures were not extractable via search. Needs direct confirmation., although you should confirm the requirement for your particular property with Lanier County Planning and Zoning (construction permits are physically obtained at the Lanier County Tax Assessor's Office, coordinated with Planning & Zoning, Code Enforcement, and Inspections). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
Teeterville, Lanier County — At a Glance
- Permit Authority Name
- Lanier County Planning and Zoning (construction permits are physically obtained at the Lanier County Tax Assessor's Office, coordinated with Planning & Zoning, Code Enforcement, and Inspections)
- Permit Authority Url
- https://laniercountyboc.com/wp/panning-and-zoning/
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation at the Tax Assessor's Office (229-482-2090).
- Setback Feet Side Rear
- Not confirmed — the Lanier County Unincorporated Zoning Ordinance (Chapter 4, Land Development Districts / Chapter 6, Development Standards) likely contains a setback table, but specific figures were not extractable via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Lanier County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 156.2
- Drive Minutes
- 213
- Nearby Towns
- Lakeland, Stockton, New Lois, Ray City
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Teeterville and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Teeterville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://laniercountyboc.com/wp/panning-and-zoning/ (2026)
- No primary source found (2026)
- https://www.zoneomics.com/code/lanier-county-unincorporated-GA/chapter_4 — verify against the primary ordinance held by the county (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Lanier County is inland (south-central GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
