Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Woodstock, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Charleston.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Benton Metal Depot is approximately 151.5 miles from Woodstock.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Delivery to Woodstock is currently estimated at 1 to 2 weeks.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
120
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Detached accessory structures must comply with all applicable setback standards of the Zoning and Land Development Regulations, but the specific side/rear footage by district was not retrieved from available excerpts.
As of 2026 · Source |
| Wind load zone |
Charleston County is a Coastal High-Hazard Area — secondary sources cite design wind speeds in roughly the 130-150 mph range (ASCE 7-16/7-22, Risk Category II), with the wind-borne debris region extending about 1 mile inland from the coast. Exact figure depends on precise parcel location and adopted county wind map; must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
191
As of 2026 · Source |
Permits & Setbacks in Charleston County
Charleston's permitting office, Charleston County Building Inspection Services, sets the accessory-structure line at 120 square feet — build under that and you generally skip the full building-permit process, though a setback of Detached accessory structures must comply with all applicable setback standards of the Zoning and Land Development Regulations, but the specific side/rear footage by district was not retrieved from available excerpts. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Woodstock
Residents in Woodstock are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 151.5 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Charleston County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Charleston County Building Inspection Services. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Woodstock?
That depends on the garage and the requirements of Charleston County Building Inspection Services. The current rule requires a permit once the garage exceeds 120 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Woodstock, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Charleston County Building Inspection Services has requirements that can affect garage placement, including a current setback of Detached accessory structures must comply with all applicable setback standards of the Zoning and Land Development Regulations, but the specific side/rear footage by district was not retrieved from available excerpts.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How far is Benton Metal Depot from Woodstock?
Benton Metal Depot's Statesboro location is approximately 151.5 miles from Woodstock. The company serves residents throughout Charleston, including communities such as Tranquil Acres, Caromi Village, Ladson and Stallsville. Current delivery time for a metal garage to the Woodstock area is about 1 to 2 weeks.
Definitions
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Woodstock, Charleston County — At a Glance
- Permit Authority Name
- Charleston County Building Inspection Services
- Permit Authority Url
- https://www.charlestoncounty.org/departments/building-inspection-services/
- Permit Threshold Sqft
- 120
- Setback Feet Side Rear
- Detached accessory structures must comply with all applicable setback standards of the Zoning and Land Development Regulations, but the specific side/rear footage by district was not retrieved from available excerpts.
- Wind Load Zone
- Charleston County is a Coastal High-Hazard Area — secondary sources cite design wind speeds in roughly the 130-150 mph range (ASCE 7-16/7-22, Risk Category II), with the wind-borne debris region extending about 1 mile inland from the coast. Exact figure depends on precise parcel location and adopted county wind map; must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- 1
- Drive Miles
- 151.5
- Drive Minutes
- 191
- Nearby Towns
- Tranquil Acres, Caromi Village, Ladson, Stallsville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Woodstock, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Woodstock?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.charlestoncounty.org/departments/building-inspection-services/ (2026)
- Charleston County Zoning and Land Development Regulations, Sec. 3.8.2(D) (https://online.encodeplus.com/regs/charlestoncounty-sc/ereader/zldr) — a Zoning Permit is not required for one detached one-story accessory structure (tool/storage shed, playhouse, or similar) if the building footprint does not exceed 120 sq ft; this exemption applies to only one such structure per lot, and it covers the zoning permit specifically — garages and structures with electrical/plumbing typically still require a building permit regardless of size. (2026)
- Charleston County Zoning and Land Development Regulations, Sec. 3.8.2(D), https://online.encodeplus.com/regs/charlestoncounty-sc/ereader/zldr — needs direct lookup of the district-specific yard table (2026)
- Aggregated from windload.solutions and similar secondary sources — no single primary Charleston County wind-speed map document was retrieved (2026)
- Given/client spec — Charleston County is a coastal South Carolina county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Charleston County
See the Charleston County hub for metal garages
