Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Tarboro can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Jasper and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not confirmed — Jasper County Code Title 20 (Zoning) contains a district-by-district setback table but exact figures were not extractable via search. Needs direct confirmation with Planning and Building Services (843-717-3650)..
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Benton serves Tillman, New Landing, Haddonville and Clyo and other communities around Tarboro.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed — Jasper County Code Title 20 (Zoning) contains a district-by-district setback table but exact figures were not extractable via search. Needs direct confirmation with Planning and Building Services (843-717-3650).
As of 2026 · Source |
| Wind load zone |
Coastal/near-coastal South Carolina — secondary sources place Jasper County in a Coastal High Hazard range of roughly 130-150 mph (ASCE 7-16, 3-second gust), likely tapering toward the lower end moving inland from the coast toward Ridgeland/Hardeeville. This is NOT a verified county-specific figure — South Carolina jurisdictions may reference ASCE 7-10 or ASCE 7-16 depending on local adoption, and the exact design wind speed for a given parcel must be confirmed with a SC-licensed engineer, the ATC Hazards by Location tool, or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
104
As of 2026 · Source |
Permits & Setbacks in Jasper County
Jasper treats a metal garage like any other accessory structure: under 200 square feet, Jasper County Planning and Building Services Department typically doesn't require a full permit, but the Not confirmed — Jasper County Code Title 20 (Zoning) contains a district-by-district setback table but exact figures were not extractable via search. Needs direct confirmation with Planning and Building Services (843-717-3650). setback rule still governs where it can sit on the lot.
Delivery to Tarboro
The current estimate for getting a metal garage to Tarboro is 1 to 2 weeks. The area is about 52.5 miles (104 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Jasper County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Jasper County Planning and Building Services Department has requirements that can affect garage placement, including a current setback of Not confirmed — Jasper County Code Title 20 (Zoning) contains a district-by-district setback table but exact figures were not extractable via search. Needs direct confirmation with Planning and Building Services (843-717-3650).. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Tarboro?
That depends on the garage and the requirements of Jasper County Planning and Building Services Department. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Jasper County Planning and Building Services Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Definitions
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
Tarboro, Jasper County — At a Glance
- Permit Authority Name
- Jasper County Planning and Building Services Department
- Permit Authority Url
- https://www.jaspercountysc.gov/services/planning-and-building/
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed — Jasper County Code Title 20 (Zoning) contains a district-by-district setback table but exact figures were not extractable via search. Needs direct confirmation with Planning and Building Services (843-717-3650).
- Wind Load Zone
- Coastal/near-coastal South Carolina — secondary sources place Jasper County in a Coastal High Hazard range of roughly 130-150 mph (ASCE 7-16, 3-second gust), likely tapering toward the lower end moving inland from the coast toward Ridgeland/Hardeeville. This is NOT a verified county-specific figure — South Carolina jurisdictions may reference ASCE 7-10 or ASCE 7-16 depending on local adoption, and the exact design wind speed for a given parcel must be confirmed with a SC-licensed engineer, the ATC Hazards by Location tool, or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 52.5
- Drive Minutes
- 104
- Nearby Towns
- Tillman, New Landing, Haddonville, Clyo
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Tarboro and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Tarboro?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.jaspercountysc.gov/services/planning-and-building/ (2026)
- Jasper County Code § 20.90.060 (Improvement Location Permit), as cited by https://jasper.county.codes/JCC/20.90.060 and summarized by secondary sources: "residential accessory structures less than 200 square feet, commercial accessory structures less than 120 square feet" are exempt from a building permit (zoning/setback compliance still required). Verify against the primary code text directly. (2026)
- https://www.jaspercountysc.gov/services/planning-and-building/ordinances-regulations/ (2026)
- Aggregated from windload.solutions (South Carolina Wind Load Requirements) and general ASCE 7-16 coastal SC guidance — no Jasper County-specific primary map source found (2026)
- Given/client spec — Jasper County, SC is a coastal county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Jasper County
See the Jasper County hub for metal garages
