Reviewed by the Benton Metal Depot team · Updated
Do you need a dedicated place where you can work in Rogers? A workshop gives you room for tools, equipment, storage and projects so you don't take over the garage. Benton Metal Depot supplies metal shop buildings throughout Jenkins, with buildings that can be customized to the type of work you actually expect to do inside.
Key Points
- ◦In Rogers, a permit from Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration) is required once the workshop exceeds Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet.
- ◦Decide on the final building dimensions before completing permanent site work.
- ◦Door size and placement should account for the largest equipment you expect to move into the shop.
- ◦Current lead time for a metal shop building to Rogers is 1 to 2 weeks.
- ◦Benton's metal shop buildings use 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. panels.
At a Glance
| Permit threshold |
Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on the ASCE 7 edition Jenkins County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
39
As of 2026 · Source |
Permits & Setbacks in Jenkins County
A workshop may fit on the property without fitting the local building rules. If you're planning a shop in Rogers, start by checking with Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration). The permit requirement applies once the building exceeds Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet, and the current setback is Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.. Getting those answers early gives you a better idea of how much of the property is actually available for the building before site preparation starts.
Delivery to Rogers
Use the delivery window to get everything else lined up before the workshop is ready. The typical lead time for a metal shop building to Rogers is 1 to 2 weeks. That gives you time to handle permits and coordinate any grading, concrete or other site work. The goal is to have the property ready without scrambling when delivery gets close.
Representative product photo — a Jenkins County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How tall should my metal shop building be?
Think about what's going through the doors and what will happen inside. Taller vehicles, equipment, lifts or overhead storage can all affect the height you need. Don't choose wall height based only on how the building looks from outside. Make sure the interior clearance works with both your current equipment and anything you're likely to add later.
What size metal shop building do I need?
Start with your largest equipment and work backward from there. Add space for workbenches, toolboxes, shelving and clear walking areas. If vehicles or machinery will be worked on inside, allow room around them rather than just enough space to park them. It's also smart to plan for tools or equipment you may add later.
What kind of panels are used on Benton metal workshops?
Benton's metal shop buildings use 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. panels. The panel specification is worth checking when you're comparing workshops because the metal roofing and siding make up the exterior envelope of the structure. Benton manufactures metal building products in Statesboro and can quote the materials based on the specifications of the workshop you want to get.
How long does it take to get a metal shop building?
Lead time to Rogers is approximately 1 to 2 weeks. You can use that period to work through permits and any site preparation the project requires. If you're coordinating concrete or contractors, base their schedules on the timeline of your order rather than a general estimate.
What should I do before pouring a slab for my workshop?
Finalize the building dimensions and confirm the local requirements first. You don't want to discover after the concrete is down that the slab is the wrong size or the shop is sitting too close to a property line. Check the requirements with Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration) and coordinate the concrete dimensions with the specifications for your actual building.
Do I need a permit for a workshop in Rogers?
The requirements in Rogers are handled by Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration). Currently, a permit is required once the building exceeds Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet. Other local rules can affect the building location as well, so check the requirements before pouring concrete or doing permanent site work. It's easier to change the plan before the property has been prepared.
How many workshop colors can I choose from?
There are currently 7 colors available for metal shop buildings. Color can be purely a matter of preference, or you may want the shop to coordinate with your home, barn or another building already on the property. It's worth looking at the available finishes before finalizing the exterior rather than treating color as a last-minute decision.
How should I plan the doors on a metal workshop?
Start with the largest thing that needs to pass through them. Vehicles, tractors, machinery and other equipment can require more clearance than a standard entry. Then think about where those items need to go once they're inside. Good door placement lets you move equipment without constantly rearranging tools, workbenches or stored materials.
Definitions
- ◦ Ventilation
- The movement of air into and out of the workshop to help manage heat, moisture, fumes or airborne material produced by certain types of work.
- ◦ Concrete Slab
- A poured concrete surface that can serve as the shop floor and part of the building's foundation system when the design calls for one.
- ◦ Roof Pitch
- The slope of the roof, expressed by how much it rises over a given horizontal distance.
- ◦ Overhead Door
- A large door that opens upward and is commonly used for vehicle, machinery or equipment access.
- ◦ Panel Gauge
- A measurement associated with the thickness of sheet metal.
- ◦ Clear Span
- Open interior space between the building's exterior supports without columns interrupting the work area.
- ◦ Walk Door
- A standard entry door for people, so the larger equipment or vehicle door doesn't have to be opened every time someone enters.
- ◦ Setback
- The minimum distance the workshop must remain from a property line, road or another boundary covered by local rules.
- ◦ Lead Time
- The period between ordering or finalizing the shop package and the point when it is ready for the next stage.
- ◦ Eave Height
- The height of the shop's sidewall where it meets the lower edge of the roof.
Rogers, Jenkins County — At a Glance
- Permit Authority Name
- Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration)
- Permit Authority Url
- https://www.jenkinscountyga.com/jenkins-county-administration.php
- Permit Threshold Sqft
- Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on the ASCE 7 edition Jenkins County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 29.9
- Drive Minutes
- 39
- Nearby Towns
- Lawton, Scarboro, Paramore Hill, Birdsville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
A useful workshop starts with how you're going to work inside it. The building needs enough room for your equipment, tools and storage, along with doors that make sense for what moves in and out. Benton Metal Depot works with customers on metal building projects and supplies the panels, trim and related materials needed to bring those plans together.
Ready to talk through your workshops project in Rogers?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for workshops specifically. (2026)
- https://www.jenkinscountyga.com/jenkins-county-administration.php — needs direct confirmation by phone (478-982-2563 / 478-982-4683) (2026)
- https://www.jenkinscountyga.com/jenkins-county-administration.php (2026)
- General GA IRC baseline exemption (120 sq ft) — no Jenkins County-specific page found (2026)
- Not found (2026)
- General ASCE 7 inland-Georgia range (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Given/client spec — Jenkins County is inland Georgia (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
