Reviewed by the Benton Metal Depot team · Updated
Are you repairing equipment, working on vehicles or simply need a place for hobbies and projects? A metal shop building gives you a workspace that's separate from the house. Benton Metal Depot supplies workshop packages to residents in Grover and surrounding communities, with 7 colors available and a lead time of 1 to 2 weeks.
Key Points
- ◦Current lead time for a metal shop building to Grover is 1 to 2 weeks.
- ◦Benton Metal Depot is approximately 111.8 miles from Grover.
- ◦In Grover, a permit from Dorchester County Building Services Department is required once the workshop exceeds 200 square feet.
- ◦Plan enough moving room around workbenches, tools and equipment to work comfortably.
- ◦Door size and placement should account for the largest equipment you expect to move into the shop.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
As of 2026 · Source |
| Wind load zone |
Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
149
As of 2026 · Source |
Permits & Setbacks in Dorchester County
A workshop may fit on the property without fitting the local building rules. If you're planning a shop in Grover, start by checking with Dorchester County Building Services Department. The permit requirement applies once the building exceeds 200 square feet, and the current setback is Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.. Getting those answers early gives you a better idea of how much of the property is actually available for the building before site preparation starts.
Delivery to Grover
Use the delivery window to get everything else lined up before the workshop is ready. The typical lead time for a metal shop building to Grover is 1 to 2 weeks. That gives you time to handle permits and coordinate any grading, concrete or other site work. The goal is to have the property ready without scrambling when delivery gets close.
Representative product photo — a Dorchester County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What size metal shop building do I need?
Start with your largest equipment and work backward from there. Add space for workbenches, toolboxes, shelving and clear walking areas. If vehicles or machinery will be worked on inside, allow room around them rather than just enough space to park them. It's also smart to plan for tools or equipment you may add later.
What kind of panels are used on Benton metal workshops?
Benton's metal shop buildings use 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. panels. The panel specification is worth checking when you're comparing workshops because the metal roofing and siding make up the exterior envelope of the structure. Benton manufactures metal building products in Statesboro and can quote the materials based on the specifications of the workshop you want to get.
How tall should my metal shop building be?
Think about what's going through the doors and what will happen inside. Taller vehicles, equipment, lifts or overhead storage can all affect the height you need. Don't choose wall height based only on how the building looks from outside. Make sure the interior clearance works with both your current equipment and anything you're likely to add later.
What should I do before pouring a slab for my workshop?
Finalize the building dimensions and confirm the local requirements first. You don't want to discover after the concrete is down that the slab is the wrong size or the shop is sitting too close to a property line. Check the requirements with Dorchester County Building Services Department and coordinate the concrete dimensions with the specifications for your actual building.
How long does it take to get a metal shop building?
Lead time to Grover is approximately 1 to 2 weeks. You can use that period to work through permits and any site preparation the project requires. If you're coordinating concrete or contractors, base their schedules on the timeline of your order rather than a general estimate.
Should I insulate my metal workshop?
That depends on how you'll use the shop and how much time you'll spend inside it. If heating, cooling or interior comfort matters, insulation is worth considering during the planning stage. Benton lists insulation products among its building accessories, but the appropriate system depends on the building and project requirements. Plan for it before finishing the interior.
How should I plan the doors on a metal workshop?
Start with the largest thing that needs to pass through them. Vehicles, tractors, machinery and other equipment can require more clearance than a standard entry. Then think about where those items need to go once they're inside. Good door placement lets you move equipment without constantly rearranging tools, workbenches or stored materials.
How many workshop colors can I choose from?
There are currently 7 colors available for metal shop buildings. Color can be purely a matter of preference, or you may want the shop to coordinate with your home, barn or another building already on the property. It's worth looking at the available finishes before finalizing the exterior rather than treating color as a last-minute decision.
Definitions
- ◦ Roof Pitch
- The slope of the roof, expressed by how much it rises over a given horizontal distance.
- ◦ Overhead Door
- A large door that opens upward and is commonly used for vehicle, machinery or equipment access.
- ◦ Setback
- The minimum distance the workshop must remain from a property line, road or another boundary covered by local rules.
- ◦ Lead Time
- The period between ordering or finalizing the shop package and the point when it is ready for the next stage.
- ◦ Ventilation
- The movement of air into and out of the workshop to help manage heat, moisture, fumes or airborne material produced by certain types of work.
- ◦ Concrete Slab
- A poured concrete surface that can serve as the shop floor and part of the building's foundation system when the design calls for one.
- ◦ Clear Span
- Open interior space between the building's exterior supports without columns interrupting the work area.
- ◦ Panel Gauge
- A measurement associated with the thickness of sheet metal.
- ◦ Walk Door
- A standard entry door for people, so the larger equipment or vehicle door doesn't have to be opened every time someone enters.
- ◦ Building Permit
- Local government approval allowing construction to proceed under the building and zoning requirements that apply to the project.
Grover, Dorchester County — At a Glance
- Permit Authority Name
- Dorchester County Building Services Department
- Permit Authority Url
- https://www.dorchestercountysc.gov/government/building-services/submittal-process
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
- Wind Load Zone
- Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 111.8
- Drive Minutes
- 149
- Nearby Towns
- Byrd, Rosinville, St. George, Badham
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal building products in Statesboro and has served the region since 2004. The company works with residential, agricultural and commercial projects and uses a single-source coil supplier to maintain consistency in its metal products. Customers in Grover can request a workshop quote based on the size and specifications of their project.
Ready to talk through your workshops project in Grover?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for workshops specifically. (2026)
- https://www.dorchestercountysc.gov/government/building-services (2026)
- https://www.dorchestercountysc.gov/government/building-services/submittal-process (2026)
- South Carolina Residential Code § R105.2 (2018 IRC as adopted statewide, incl. Dorchester County): one-story detached accessory structures used as tool/storage sheds, playhouses, etc. are exempt from a building permit if floor area ≤200 sq ft AND the structure has no electrical/plumbing/mechanical connections. Not independently re-confirmed on Dorchester's own permitting page (403'd on fetch) — verify against Dorchester's current submittal guide before publishing. (2026)
- https://www.dorchestercountysc.gov/government/planning-development/planning-zoning/zoning-and-land-development-standards (2026)
- General ASCE 7 coastal-plain-SC range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Dorchester County is not among the coastal counties named in the client spec, though it borders Charleston and Berkeley counties (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
