Horse Barns in Pine Hill 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated November 10, 2026

If you're building a horse barn in Pine Hill, don't plan around stalls alone. You'll also need to think about airflow, water access, feed, tack and where the horses will enter and leave. Benton Metal Depot supplies metal building materials throughout Jefferson, with 7 exterior colors available for applicable packages.

Key Points

◦The current local setback for a horse barn in Pine Hill is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text..
◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
◦Aisle width should allow horses and handlers to move comfortably and safely.
◦Ventilation, drainage and access to fresh water should be considered during barn planning.
◦Plan stall dimensions around the horses that will actually use them.

At a Glance

Permit threshold	No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. As of 2026 · Source
Setback (side/rear)	Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. As of 2026 · Source
Wind load zone	Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels As of 2026 · Source
Drive time from Statesboro	84 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Jefferson County

Check the building rules before you settle on a location for the barn. Horse barn permit requirements in Pine Hill are handled by Jefferson County Building Permits & Inspections / Code Enforcement Department. The current threshold is No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet, but building size may not be the only consideration. Zoning, setbacks and how the property will be used can also affect the project. Confirm those details before preparing the site or beginning permanent construction work.

Delivery to Pine Hill

Don't wait until the barn materials are ready to start thinking about the site. Customers in Pine Hill are currently looking at 1 to 2 weeks from Statesboro. Benton Metal Depot is about 60.1 miles away. Use that time to coordinate contractors and prepare the area where materials will be received.

Representative product photo — a Jefferson County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Can I add a tack room and wash area to my horse barn?

Yes, those spaces can be included in the overall barn plan when the layout and building dimensions allow. A tack room needs practical storage, while a wash area needs suitable drainage and water access. Decide where both belong before choosing the final building size, since they can take up space you might otherwise assign to stalls or aisles.

Do I need a permit for a horse barn in Pine Hill?

The requirements for Pine Hill are handled by Jefferson County Building Permits & Inspections / Code Enforcement Department. Currently, a permit is required once the barn exceeds No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet. Agricultural use doesn't automatically mean a building is exempt from every local rule. Check zoning, setbacks and any other requirements for your property before beginning site work or committing to the barn's location.

Is a metal horse barn too hot for Georgia summers?

A metal roof or wall system doesn't determine barn comfort by itself. Ventilation, insulation where appropriate, shade and the overall building design all affect interior conditions. In Pine Hill, plan for the region's warm, humid weather. Horses need adequate airflow and access to fresh water, so those requirements should be part of the design from the beginning.

How many colors are available for a horse barn?

Benton's applicable horse barn materials are available in 7 colors. You may want the barn to match existing buildings, or you may prefer a traditional farm-building appearance. Color is worth choosing early, especially if the roof and walls will have different finishes. Confirm the available combinations before finalizing the material order.

How wide should the aisle in a horse barn be?

The aisle needs enough room for horses and handlers to move without crowding doors, corners or stored equipment. Think about how horses will enter and leave stalls, whether you'll move wheelbarrows through the barn and how daily cleaning will work. Have the layout reviewed for safe horse handling rather than choosing an aisle width based only on available space.

How close can I build a horse barn to my property line?

The current setback in Pine Hill is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text., subject to the requirements of Jefferson County Building Permits & Inspections / Code Enforcement Department and your property. There may also be separate rules affecting livestock buildings or where animals can be kept. Check those requirements before marking the barn location, particularly if neighboring homes or property boundaries are nearby.

Can I store hay and feed inside my horse barn?

You can plan storage areas for feed and supplies, but hay storage deserves special attention because of fire risk, moisture and dust. Many barn designs separate bulk hay from horse housing. Think about how feed will be delivered, kept dry and accessed every day. Review the storage arrangement with a qualified equine facility professional before construction.

What size should horse stalls be?

Stall size depends on the horse, including its height, build and how comfortably it can turn around and lie down. A layout suitable for one horse may not work for a larger animal or a mare with a foal. Have an experienced equine facility designer or qualified professional review the stall dimensions before construction.

Definitions

◦ Feed Room: A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
◦ Post-Frame Construction: A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
◦ Roof Pitch: The slope of the barn roof, usually described by how much it rises over a set horizontal distance.
◦ Eave Height: The height of the barn's exterior wall where it meets the lower edge of the roof.
◦ Setback: The required distance between a barn and a property boundary, road or another feature covered by local building or zoning rules.
◦ Tack Room: A dedicated area for storing saddles, bridles, grooming supplies and other horse equipment.
◦ Lead Time: The period needed to process and prepare the building materials after the relevant order stage.
◦ Stall Partition: A wall or divider separating one horse stall from another or from an adjacent area.
◦ Panel Gauge: A measurement related to sheet-metal thickness.
◦ Condensation: Moisture that forms when humid air contacts a sufficiently cool surface. Poorly managed condensation can cause damp conditions inside a barn.

Pine Hill, Jefferson County — At a Glance

Permit Authority Name: Jefferson County Building Permits & Inspections / Code Enforcement Department
Permit Authority Url: https://www.jeffersoncountyga.gov/184/Building-Permit-Procedure
Permit Threshold Sqft: No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification.
Setback Feet Side Rear: Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.
Wind Load Zone: Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
Coastal
Drive Miles: 60.1
Drive Minutes: 84
Nearby Towns: Moxley, Wadley, Almira, Bartow
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels
Color Count: 7

Why Benton Metal Depot

A horse barn involves more planning than choosing a roof and four walls. You have to think about the animals, the people caring for them and how the building will be used every day. Benton Metal Depot supplies metal panels, trim and related building materials for agricultural projects, allowing customers to coordinate those exterior materials with the rest of their barn plans.

Ready to talk through your horse barns project in Pine Hill?

Call (912) 489-5795

Sources

Other Cities We Serve in Jefferson County

See the Jefferson County hub for horse barns

Almira Atwell Avera Bartow Ellis Plantation Louisville Matthews Moxley Noah Old Town Omaha Springs Pine Hill Stapleton Stapletons Crossroads Stellaville Wadley Wrens Zebina

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Horse Barns for your Horse Barns in Pine Hill, Jefferson County, Georgia (2026)