Horse Barns in Stellaville 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated November 10, 2026

Do you have one horse, or several of them? It's important that the barn is suitable for both the animals and the people caring for them. Benton Metal Depot serves customers in Stellaville and throughout Jefferson with agricultural metal building materials, including 29-gauge and 26-gauge Rib panels panels for applicable barn packages.

Key Points

◦Applicable Benton horse barn packages use 29-gauge and 26-gauge Rib panels metal panels.
◦The current local setback for a horse barn in Stellaville is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text..
◦Benton Metal Depot is approximately 76.4 miles from Stellaville.
◦Horse barn exterior materials are available in 7 colors.
◦Plan stall dimensions around the horses that will actually use them.

At a Glance

Permit threshold	No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. As of 2026 · Source
Setback (side/rear)	Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. As of 2026 · Source
Wind load zone	Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels As of 2026 · Source
Drive time from Statesboro	100 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Jefferson County

Barn placement is something to figure out before the ground is cleared. If you're planning a horse barn in Stellaville, contact Jefferson County Building Permits & Inspections / Code Enforcement Department about the local requirements. The permit rule applies once the building exceeds No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet, and the current setback is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.. You should also check whether any additional rules apply to keeping horses on the property before committing to a building location.

Delivery to Stellaville

Don't wait until the barn materials are ready to start thinking about the site. Customers in Stellaville are currently looking at 1 to 2 weeks from Statesboro. Benton Metal Depot is about 76.4 miles away. Use that time to coordinate contractors and prepare the area where materials will be received.

Representative product photo — a Jefferson County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Do I need a permit for a horse barn in Stellaville?

The requirements for Stellaville are handled by Jefferson County Building Permits & Inspections / Code Enforcement Department. Currently, a permit is required once the barn exceeds No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet. Agricultural use doesn't automatically mean a building is exempt from every local rule. Check zoning, setbacks and any other requirements for your property before beginning site work or committing to the barn's location.

How many colors are available for a horse barn?

Benton's applicable horse barn materials are available in 7 colors. You may want the barn to match existing buildings, or you may prefer a traditional farm-building appearance. Color is worth choosing early, especially if the roof and walls will have different finishes. Confirm the available combinations before finalizing the material order.

Should a horse barn have insulation?

That depends on the building design, local climate and how the barn will be used. Insulation may help manage heat transfer and condensation, but it doesn't replace ventilation. In horse housing, airflow and moisture control are important. Discuss the complete roof and wall assembly with the building designer before choosing insulation materials or enclosing the interior.

What kind of floor is best for a horse barn?

Different parts of the barn may need different flooring. Stalls, aisles, wash areas and storage rooms don't necessarily work best with the same surface. Drainage, footing, cleaning and slip resistance should guide the decision. Plan the floor system with someone familiar with horse facilities before installing concrete or other permanent surfaces.

How close can I build a horse barn to my property line?

The current setback in Stellaville is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text., subject to the requirements of Jefferson County Building Permits & Inspections / Code Enforcement Department and your property. There may also be separate rules affecting livestock buildings or where animals can be kept. Check those requirements before marking the barn location, particularly if neighboring homes or property boundaries are nearby.

What size should horse stalls be?

Stall size depends on the horse, including its height, build and how comfortably it can turn around and lie down. A layout suitable for one horse may not work for a larger animal or a mare with a foal. Have an experienced equine facility designer or qualified professional review the stall dimensions before construction.

How big should a horse barn be?

Start with the number and size of your horses, then add the space needed for safe handling and daily care. Stalls are only one part of the layout. You'll also need room for aisles, doors, feed, tack and possibly a wash area. If you expect to add horses later, think about that before choosing the building dimensions.

What kind of metal panels does Benton use for horse barns?

The applicable horse barn package uses 29-gauge and 26-gauge Rib panels panels. Metal roofing and siding help enclose the building and protect it from the weather, but panel selection is only part of planning a barn. Ventilation, condensation control and the safety of surfaces horses can reach should also be addressed in the finished design.

Definitions

◦ Ridge Vent: A ventilation opening near the roof peak that allows warm, moist air to escape when designed as part of a functioning ventilation system.
◦ Stall Partition: A wall or divider separating one horse stall from another or from an adjacent area.
◦ Tack Room: A dedicated area for storing saddles, bridles, grooming supplies and other horse equipment.
◦ Eave Height: The height of the barn's exterior wall where it meets the lower edge of the roof.
◦ Post-Frame Construction: A building method that uses regularly spaced structural posts or columns to support the roof and walls. It's commonly used for agricultural buildings.
◦ Feed Room: A space used to store and organize feed and feeding supplies, with appropriate protection from moisture and pests.
◦ Condensation: Moisture that forms when humid air contacts a sufficiently cool surface. Poorly managed condensation can cause damp conditions inside a barn.
◦ Lead Time: The period needed to process and prepare the building materials after the relevant order stage.
◦ Panel Gauge: A measurement related to sheet-metal thickness.
◦ Dutch Door: A door divided into upper and lower sections that can open separately. Some horse barns use them for stall or exterior access.

Stellaville, Jefferson County — At a Glance

Permit Authority Name: Jefferson County Building Permits & Inspections / Code Enforcement Department
Permit Authority Url: https://www.jeffersoncountyga.gov/184/Building-Permit-Procedure
Permit Threshold Sqft: No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification.
Setback Feet Side Rear: Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.
Wind Load Zone: Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
Coastal
Drive Miles: 76.4
Drive Minutes: 100
Nearby Towns: Zebina, Ellis Plantation, Atwell, Wrens
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot has served contractors and property owners from Statesboro since 2004. The company manufactures metal roofing products and uses a single-source coil supplier to help maintain color consistency. For customers building a horse barn in Stellaville, Benton can supply applicable metal roofing and siding materials based on the project's specifications and selected finishes.

Ready to talk through your horse barns project in Stellaville?

Call (912) 489-5795

Sources

Other Cities We Serve in Jefferson County

See the Jefferson County hub for horse barns

Almira Atwell Avera Bartow Ellis Plantation Louisville Matthews Moxley Noah Old Town Omaha Springs Pine Hill Stapleton Stapletons Crossroads Stellaville Wadley Wrens Zebina

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Horse Barns for your Horse Barns in Stellaville, Jefferson County, Georgia (2026)