Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Coffee, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Bacon and the surrounding area.
Key Points
- ◦Benton serves Mershon, Bristol, Trudie and Aspinwall and other communities around Coffee.
- ◦In Coffee, a building permit is required once the garage exceeds Not found. No county-published permit-exemption sqft threshold was located online. Needs direct county contact. square feet.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county..
At a Glance
| Permit threshold |
Not found. No county-published permit-exemption sqft threshold was located online. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county.
As of 2026 · Source |
| Wind load zone |
Inland southeast Georgia coastal plain — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
120
As of 2026 · Source |
Permits & Setbacks in Bacon County
The permit question for a Coffee metal garage comes down to one number from Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site): Not found. No county-published permit-exemption sqft threshold was located online. Needs direct county contact. square feet. Stay under it and skip the full permit process; either way, keep the Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county. setback in mind before you pick a spot.
Delivery to Coffee
Current delivery time to Coffee is approximately 1 to 2 weeks. Benton also serves nearby communities including Mershon, Bristol, Trudie and Aspinwall. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Bacon County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How far is Benton Metal Depot from Coffee?
Benton Metal Depot's Statesboro location is approximately 78 miles from Coffee. The company serves residents throughout Bacon, including communities such as Mershon, Bristol, Trudie and Aspinwall. Current delivery time for a metal garage to the Coffee area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Coffee is Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county., although you should confirm the requirement for your particular property with Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Coffee, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Coffee before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Coffee?
Current delivery time to Coffee is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site) has requirements that can affect garage placement, including a current setback of Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Definitions
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
Coffee, Bacon County — At a Glance
- Permit Authority Name
- Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site)
- Permit Authority Url
- https://baconcounty.org/
- Permit Threshold Sqft
- Not found. No county-published permit-exemption sqft threshold was located online. Needs direct county contact.
- Setback Feet Side Rear
- Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county.
- Wind Load Zone
- Inland southeast Georgia coastal plain — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 78
- Drive Minutes
- 120
- Nearby Towns
- Mershon, Bristol, Trudie, Aspinwall
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Coffee and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Coffee?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://baconcounty.org/ (2026)
- No county-specific source located; a 1970s zoning ordinance for Alma/Bacon County exists per NTIS record PB209068 but is not available online (2026)
- https://ntrl.ntis.gov/NTRL/dashboard/searchResults/titleDetail/PB209068.xhtml (ordinance exists but not retrievable online) (2026)
- General ASCE 7 inland-southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Bacon County is inland (~50+ miles from the Atlantic) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
