Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Rockingham? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Bacon, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 93.9 miles from Rockingham.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Rockingham is currently estimated at 1 to 2 weeks.
At a Glance
| Permit threshold |
Not found. No county-published permit-exemption sqft threshold was located online. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county.
As of 2026 · Source |
| Wind load zone |
Inland southeast Georgia coastal plain — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
122
As of 2026 · Source |
Permits & Setbacks in Bacon County
The permit question for a Rockingham metal garage comes down to one number from Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site): Not found. No county-published permit-exemption sqft threshold was located online. Needs direct county contact. square feet. Stay under it and skip the full permit process; either way, keep the Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county. setback in mind before you pick a spot.
Delivery to Rockingham
Metal garage delivery to Rockingham can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Bacon County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Rockingham?
That depends on the garage and the requirements of Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site). The current rule requires a permit once the garage exceeds Not found. No county-published permit-exemption sqft threshold was located online. Needs direct county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Rockingham, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site) has requirements that can affect garage placement, including a current setback of Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How long does it take to get a metal garage delivered to Rockingham?
Current delivery time to Rockingham is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Definitions
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
Rockingham, Bacon County — At a Glance
- Permit Authority Name
- Bacon County Building Department / Building Inspector (exact current department name not confirmed — no dedicated permitting page found on the county's official site)
- Permit Authority Url
- https://baconcounty.org/
- Permit Threshold Sqft
- Not found. No county-published permit-exemption sqft threshold was located online. Needs direct county contact.
- Setback Feet Side Rear
- Not found. No accessible online zoning ordinance text was located for Bacon County. Needs direct confirmation with the county.
- Wind Load Zone
- Inland southeast Georgia coastal plain — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 93.9
- Drive Minutes
- 122
- Nearby Towns
- New Lacy, Guysie, Alma, Wilsonville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Rockingham and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Rockingham?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://baconcounty.org/ (2026)
- No county-specific source located; a 1970s zoning ordinance for Alma/Bacon County exists per NTIS record PB209068 but is not available online (2026)
- https://ntrl.ntis.gov/NTRL/dashboard/searchResults/titleDetail/PB209068.xhtml (ordinance exists but not retrievable online) (2026)
- General ASCE 7 inland-southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Bacon County is inland (~50+ miles from the Atlantic) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
