Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Ray City, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Berrien and the surrounding area.
Key Points
- ◦Benton serves New Lois, Teeterville, Lakeland and Allenville and other communities around Ray City.
- ◦In Ray City, a building permit is required once the garage exceeds Not found — no published sqft exemption for accessory structures located on the county site. The office does issue building permits generally, but no specific threshold was found. Needs direct confirmation (229-686-2149, option 2). square feet.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site. The office does issue building permits generally, but no specific threshold was found. Needs direct confirmation (229-686-2149, option 2).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed — the county notes its zoning ordinance "includes...building size and setbacks" but specific figures were not extractable via search. Needs direct confirmation or review of the full ordinance on Municode.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Berrien County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
227
As of 2026 · Source |
Permits & Setbacks in Berrien County
The permit question for a Ray City metal garage comes down to one number from Berrien County Code Enforcement Office (Planning and Zoning): Not found — no published sqft exemption for accessory structures located on the county site. The office does issue building permits generally, but no specific threshold was found. Needs direct confirmation (229-686-2149, option 2). square feet. Stay under it and skip the full permit process; either way, keep the Not confirmed — the county notes its zoning ordinance "includes...building size and setbacks" but specific figures were not extractable via search. Needs direct confirmation or review of the full ordinance on Municode. setback in mind before you pick a spot.
Delivery to Ray City
Current delivery time to Ray City is approximately 1 to 2 weeks. Benton also serves nearby communities including New Lois, Teeterville, Lakeland and Allenville. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Berrien County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
How long does it take to get a metal garage delivered to Ray City?
Current delivery time to Ray City is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Ray City before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
How close can my metal garage be to the property line?
The current setback in Ray City is Not confirmed — the county notes its zoning ordinance "includes...building size and setbacks" but specific figures were not extractable via search. Needs direct confirmation or review of the full ordinance on Municode., although you should confirm the requirement for your particular property with Berrien County Code Enforcement Office (Planning and Zoning). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Berrien County Code Enforcement Office (Planning and Zoning) has requirements that can affect garage placement, including a current setback of Not confirmed — the county notes its zoning ordinance "includes...building size and setbacks" but specific figures were not extractable via search. Needs direct confirmation or review of the full ordinance on Municode.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How far is Benton Metal Depot from Ray City?
Benton Metal Depot's Statesboro location is approximately 164.5 miles from Ray City. The company serves residents throughout Berrien, including communities such as New Lois, Teeterville, Lakeland and Allenville. Current delivery time for a metal garage to the Ray City area is about 1 to 2 weeks.
Definitions
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
Ray City, Berrien County — At a Glance
- Permit Authority Name
- Berrien County Code Enforcement Office (Planning and Zoning)
- Permit Authority Url
- https://berriencountygeorgia.com/planning-and-zoning/
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site. The office does issue building permits generally, but no specific threshold was found. Needs direct confirmation (229-686-2149, option 2).
- Setback Feet Side Rear
- Not confirmed — the county notes its zoning ordinance "includes...building size and setbacks" but specific figures were not extractable via search. Needs direct confirmation or review of the full ordinance on Municode.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Berrien County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 164.5
- Drive Minutes
- 227
- Nearby Towns
- New Lois, Teeterville, Lakeland, Allenville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Ray City, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Ray City?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://berriencountygeorgia.com/planning-and-zoning/ (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Berrien County is inland (south-central GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
