Reviewed by the Benton Metal Depot team · Updated
For some residents in Overbrook, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Bulloch, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦The current local setback for a metal garage is 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Overbrook, a building permit is required once the garage exceeds 200 square feet.
- ◦Benton serves Jimps, Emit, Anderson Mill and Hopeulikit and other communities around Overbrook.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on which ASCE 7 edition Bulloch County has adopted and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
6
As of 2026 · Source |
Permits & Setbacks in Bulloch County
The permit question for a Overbrook metal garage comes down to one number from Bulloch County Building Permit/Inspection Department: 200 square feet. Stay under it and skip the full permit process; either way, keep the 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building setback in mind before you pick a spot.
Delivery to Overbrook
The current estimate for getting a metal garage to Overbrook is 1 to 2 weeks. The area is about 2.2 miles (6 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Bulloch County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Bulloch County Building Permit/Inspection Department has requirements that can affect garage placement, including a current setback of 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How close can my metal garage be to the property line?
The current setback in Overbrook is 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building, although you should confirm the requirement for your particular property with Bulloch County Building Permit/Inspection Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Overbrook?
Benton Metal Depot's Statesboro location is approximately 2.2 miles from Overbrook. The company serves residents throughout Bulloch, including communities such as Jimps, Emit, Anderson Mill and Hopeulikit. Current delivery time for a metal garage to the Overbrook area is about 1 to 2 weeks.
How long does it take to get a metal garage delivered to Overbrook?
Current delivery time to Overbrook is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Overbrook before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
Overbrook, Bulloch County — At a Glance
- Permit Authority Name
- Bulloch County Building Permit/Inspection Department
- Permit Authority Url
- https://bullochcounty.net/permitting/
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on which ASCE 7 edition Bulloch County has adopted and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- Drive Miles
- 2.2
- Drive Minutes
- 6
- Nearby Towns
- Jimps, Emit, Anderson Mill, Hopeulikit
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Overbrook, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Overbrook?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://bullochcounty.net/permitting/ (2026)
- https://bullochcounty.net/permitting/ ("Structure over 200 square feet (e.g., garage, pole barn, storage building, shed)" requires a permit) (2026)
- Bulloch County Zoning Ordinance (adopted 4/4/23), Section 1403, as summarized at https://www.zoneomics.com/code/bulloch-county-unincorporated-GA/chapter_13 — verify against the primary PDF at https://bullochcounty.net/wp-content/uploads/2023/06/Appendix-C-Zoning-ADOPTED-4_4_23-002-002.pdf (text extraction failed on that PDF, so this is from a secondary source) (2026)
- General ASCE 7 inland-Georgia range (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Bulloch County is ~50 miles inland and is not among the coastal counties named in the client spec (Chatham, Bryan, Liberty, McIntosh, Glynn, Camden, Beaufort, Jasper, Colleton, Charleston) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
