Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Piddleville and across Bulloch, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦The current local setback for a metal garage is 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Piddleville, a building permit is required once the garage exceeds 200 square feet.
- ◦Benton serves Aaron, Portal, Overbrook and Jimps and other communities around Piddleville.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on which ASCE 7 edition Bulloch County has adopted and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
25
As of 2026 · Source |
Permits & Setbacks in Bulloch County
Before a metal garage goes up in Piddleville, check with Bulloch County Building Permit/Inspection Department — Bulloch's cutoff for requiring a building permit is 200 square feet. Below that, you still need to clear the 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building setback from your property line.
Delivery to Piddleville
Current delivery time to Piddleville is approximately 1 to 2 weeks. Benton also serves nearby communities including Aaron, Portal, Overbrook and Jimps. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Bulloch County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How long does it take to get a metal garage delivered to Piddleville?
Current delivery time to Piddleville is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Piddleville before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Piddleville, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How close can my metal garage be to the property line?
The current setback in Piddleville is 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building, although you should confirm the requirement for your particular property with Bulloch County Building Permit/Inspection Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Piddleville?
Benton Metal Depot's Statesboro location is approximately 16.3 miles from Piddleville. The company serves residents throughout Bulloch, including communities such as Aaron, Portal, Overbrook and Jimps. Current delivery time for a metal garage to the Piddleville area is about 1 to 2 weeks.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Bulloch County Building Permit/Inspection Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Piddleville, Bulloch County — At a Glance
- Permit Authority Name
- Bulloch County Building Permit/Inspection Department
- Permit Authority Url
- https://bullochcounty.net/permitting/
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- 10 ft from property line in AG-5/R80/R40/R25/R15/R8 districts (5 ft in R2/R3/PUD/HC/GC/NC/LI/HI); detached accessory building must also sit at least 12 ft from the principal building
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on which ASCE 7 edition Bulloch County has adopted and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- Drive Miles
- 16.3
- Drive Minutes
- 25
- Nearby Towns
- Aaron, Portal, Overbrook, Jimps
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Piddleville and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Piddleville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://bullochcounty.net/permitting/ (2026)
- https://bullochcounty.net/permitting/ ("Structure over 200 square feet (e.g., garage, pole barn, storage building, shed)" requires a permit) (2026)
- Bulloch County Zoning Ordinance (adopted 4/4/23), Section 1403, as summarized at https://www.zoneomics.com/code/bulloch-county-unincorporated-GA/chapter_13 — verify against the primary PDF at https://bullochcounty.net/wp-content/uploads/2023/06/Appendix-C-Zoning-ADOPTED-4_4_23-002-002.pdf (text extraction failed on that PDF, so this is from a secondary source) (2026)
- General ASCE 7 inland-Georgia range (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Bulloch County is ~50 miles inland and is not among the coastal counties named in the client spec (Chatham, Bryan, Liberty, McIntosh, Glynn, Camden, Beaufort, Jasper, Colleton, Charleston) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
