Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Spring Bluff and across Camden, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Spring Bluff is currently estimated at 1 to 2 weeks.
- ◦Benton Metal Depot is approximately 121.2 miles from Spring Bluff.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not found — Camden County's Unified Development Code confirms accessory structure permits exist and are processed online, but no explicit sqft exemption threshold was located. Needs direct confirmation with Planning & Development.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
15 ft minimum side yard setback for accessory buildings per UDC Sec. 222(c)(5) (a variance may be requested to reduce it); rear-yard figure and other-district figures not independently confirmed.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia (St. Marys/Kingsland) — general secondary sources place coastal GA in the ~130 mph (ASCE 7-22, Risk Category II) band, similar to Chatham/Glynn/McIntosh, but no Camden-specific primary map figure was found. Must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
151
As of 2026 · Source |
Permits & Setbacks in Camden County
Camden's permitting office, Camden County Office of Planning & Development, sets the accessory-structure line at Not found — Camden County's Unified Development Code confirms accessory structure permits exist and are processed online, but no explicit sqft exemption threshold was located. Needs direct confirmation with Planning & Development. square feet — build under that and you generally skip the full building-permit process, though a setback of 15 ft minimum side yard setback for accessory buildings per UDC Sec. 222(c)(5) (a variance may be requested to reduce it); rear-yard figure and other-district figures not independently confirmed. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Spring Bluff
Current delivery time to Spring Bluff is approximately 1 to 2 weeks. Benton also serves nearby communities including Ceylon, Salter, Piney Bluff and Dover Bluff. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Camden County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Do I need a permit for a metal garage in Spring Bluff?
That depends on the garage and the requirements of Camden County Office of Planning & Development. The current rule requires a permit once the garage exceeds Not found — Camden County's Unified Development Code confirms accessory structure permits exist and are processed online, but no explicit sqft exemption threshold was located. Needs direct confirmation with Planning & Development. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Spring Bluff, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Camden County Office of Planning & Development. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
How far is Benton Metal Depot from Spring Bluff?
Benton Metal Depot's Statesboro location is approximately 121.2 miles from Spring Bluff. The company serves residents throughout Camden, including communities such as Ceylon, Salter, Piney Bluff and Dover Bluff. Current delivery time for a metal garage to the Spring Bluff area is about 1 to 2 weeks.
Definitions
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Spring Bluff, Camden County — At a Glance
- Permit Authority Name
- Camden County Office of Planning & Development
- Permit Authority Url
- https://www.camdencountyga.gov/102/Permits
- Permit Threshold Sqft
- Not found — Camden County's Unified Development Code confirms accessory structure permits exist and are processed online, but no explicit sqft exemption threshold was located. Needs direct confirmation with Planning & Development.
- Setback Feet Side Rear
- 15 ft minimum side yard setback for accessory buildings per UDC Sec. 222(c)(5) (a variance may be requested to reduce it); rear-yard figure and other-district figures not independently confirmed.
- Wind Load Zone
- Coastal Georgia (St. Marys/Kingsland) — general secondary sources place coastal GA in the ~130 mph (ASCE 7-22, Risk Category II) band, similar to Chatham/Glynn/McIntosh, but no Camden-specific primary map figure was found. Must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 121.2
- Drive Minutes
- 151
- Nearby Towns
- Ceylon, Salter, Piney Bluff, Dover Bluff
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Spring Bluff and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Spring Bluff?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.camdencountyga.gov/102/Permits (2026)
- https://www.co.camden.ga.us/ArchiveCenter/ViewFile/Item/644 (Unified Development Code) and https://www.camdencountyga.gov/1250/Permit-Fee-Schedule (2026)
- Camden County Unified Development Code, Sec. 222(c)(5) — verify against the primary UDC document at https://www.co.camden.ga.us/ArchiveCenter/ViewFile/Item/644 (2026)
- Aggregated from windload.solutions and similar secondary sources — no Camden-specific primary map found (2026)
- Given/client spec — Camden County (St. Marys/Kingsland) is a coastal Georgia county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Camden County
See the Camden County hub for metal garages
