Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Stafford? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Camden, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Benton Metal Depot is approximately 147.7 miles from Stafford.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Stafford is currently estimated at 1 to 2 weeks.
- ◦Benton serves Dungeness, Cabin Bluff, Greyfield and Shellbine and other communities around Stafford.
At a Glance
| Permit threshold |
Not found — Camden County's Unified Development Code confirms accessory structure permits exist and are processed online, but no explicit sqft exemption threshold was located. Needs direct confirmation with Planning & Development.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
15 ft minimum side yard setback for accessory buildings per UDC Sec. 222(c)(5) (a variance may be requested to reduce it); rear-yard figure and other-district figures not independently confirmed.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia (St. Marys/Kingsland) — general secondary sources place coastal GA in the ~130 mph (ASCE 7-22, Risk Category II) band, similar to Chatham/Glynn/McIntosh, but no Camden-specific primary map figure was found. Must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
171
As of 2026 · Source |
Permits & Setbacks in Camden County
Camden treats a metal garage like any other accessory structure: under Not found — Camden County's Unified Development Code confirms accessory structure permits exist and are processed online, but no explicit sqft exemption threshold was located. Needs direct confirmation with Planning & Development. square feet, Camden County Office of Planning & Development typically doesn't require a full permit, but the 15 ft minimum side yard setback for accessory buildings per UDC Sec. 222(c)(5) (a variance may be requested to reduce it); rear-yard figure and other-district figures not independently confirmed. setback rule still governs where it can sit on the lot.
Delivery to Stafford
Residents in Stafford are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 147.7 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Camden County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Camden County Office of Planning & Development. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Stafford, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Do I need a permit for a metal garage in Stafford?
That depends on the garage and the requirements of Camden County Office of Planning & Development. The current rule requires a permit once the garage exceeds Not found — Camden County's Unified Development Code confirms accessory structure permits exist and are processed online, but no explicit sqft exemption threshold was located. Needs direct confirmation with Planning & Development. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Stafford before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Stafford?
Current delivery time to Stafford is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
Stafford, Camden County — At a Glance
- Permit Authority Name
- Camden County Office of Planning & Development
- Permit Authority Url
- https://www.camdencountyga.gov/102/Permits
- Permit Threshold Sqft
- Not found — Camden County's Unified Development Code confirms accessory structure permits exist and are processed online, but no explicit sqft exemption threshold was located. Needs direct confirmation with Planning & Development.
- Setback Feet Side Rear
- 15 ft minimum side yard setback for accessory buildings per UDC Sec. 222(c)(5) (a variance may be requested to reduce it); rear-yard figure and other-district figures not independently confirmed.
- Wind Load Zone
- Coastal Georgia (St. Marys/Kingsland) — general secondary sources place coastal GA in the ~130 mph (ASCE 7-22, Risk Category II) band, similar to Chatham/Glynn/McIntosh, but no Camden-specific primary map figure was found. Must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 147.7
- Drive Minutes
- 171
- Nearby Towns
- Dungeness, Cabin Bluff, Greyfield, Shellbine
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Stafford and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Stafford?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.camdencountyga.gov/102/Permits (2026)
- https://www.co.camden.ga.us/ArchiveCenter/ViewFile/Item/644 (Unified Development Code) and https://www.camdencountyga.gov/1250/Permit-Fee-Schedule (2026)
- Camden County Unified Development Code, Sec. 222(c)(5) — verify against the primary UDC document at https://www.co.camden.ga.us/ArchiveCenter/ViewFile/Item/644 (2026)
- Aggregated from windload.solutions and similar secondary sources — no Camden-specific primary map found (2026)
- Given/client spec — Camden County (St. Marys/Kingsland) is a coastal Georgia county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Camden County
See the Camden County hub for metal garages
