Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Donald can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Long and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Delivery to Donald is currently estimated at 1 to 2 weeks.
- ◦Benton Metal Depot is approximately 59.3 miles from Donald.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
Not explicitly published — the county maintains a Land Development Code (PDF) and a building permit application, but no clear sqft exemption threshold for accessory structures was found in it via search. Needs direct confirmation with Code Enforcement (912-545-3683 / codeenforcement@longcountyga.gov).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — the Land Development Code likely contains a setback table by district (see Planning & Zoning page), but specific figures were not extractable via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C), though Long County is closer to the coast than most counties in this batch (roughly 25-30 miles from Long County to tidewater). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
94
As of 2026 · Source |
Permits & Setbacks in Long County
The permit question for a Donald metal garage comes down to one number from Long County Code Enforcement Office: Not explicitly published — the county maintains a Land Development Code (PDF) and a building permit application, but no clear sqft exemption threshold for accessory structures was found in it via search. Needs direct confirmation with Code Enforcement (912-545-3683 / codeenforcement@longcountyga.gov). square feet. Stay under it and skip the full permit process; either way, keep the Not found — the Land Development Code likely contains a setback table by district (see Planning & Zoning page), but specific figures were not extractable via search. Needs direct confirmation. setback in mind before you pick a spot.
Delivery to Donald
Residents in Donald are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 59.3 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Long County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How close can my metal garage be to the property line?
The current setback in Donald is Not found — the Land Development Code likely contains a setback table by district (see Planning & Zoning page), but specific figures were not extractable via search. Needs direct confirmation., although you should confirm the requirement for your particular property with Long County Code Enforcement Office. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How far is Benton Metal Depot from Donald?
Benton Metal Depot's Statesboro location is approximately 59.3 miles from Donald. The company serves residents throughout Long, including communities such as Smiley Crossroads, Wefanie, Elim and Ludowici. Current delivery time for a metal garage to the Donald area is about 1 to 2 weeks.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Long County Code Enforcement Office has requirements that can affect garage placement, including a current setback of Not found — the Land Development Code likely contains a setback table by district (see Planning & Zoning page), but specific figures were not extractable via search. Needs direct confirmation.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How long does it take to get a metal garage delivered to Donald?
Current delivery time to Donald is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Donald before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Definitions
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
Donald, Long County — At a Glance
- Permit Authority Name
- Long County Code Enforcement Office
- Permit Authority Url
- https://www.longcountyga.gov/code-enforcement
- Permit Threshold Sqft
- Not explicitly published — the county maintains a Land Development Code (PDF) and a building permit application, but no clear sqft exemption threshold for accessory structures was found in it via search. Needs direct confirmation with Code Enforcement (912-545-3683 / codeenforcement@longcountyga.gov).
- Setback Feet Side Rear
- Not found — the Land Development Code likely contains a setback table by district (see Planning & Zoning page), but specific figures were not extractable via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C), though Long County is closer to the coast than most counties in this batch (roughly 25-30 miles from Long County to tidewater). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 59.3
- Drive Minutes
- 94
- Nearby Towns
- Smiley Crossroads, Wefanie, Elim, Ludowici
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Donald, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Donald?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.longcountyga.gov/code-enforcement (2026)
- https://www.longcountyga.gov/code-enforcement (Land Development Code PDF linked there) (2026)
- https://www.longcountyga.gov/planning-zoning (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Long County is not among the coastal counties named in the client spec (per provided coastal flag list) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
