Reviewed by the Benton Metal Depot team · Updated
For some residents in Blackshear, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Pierce, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦In Blackshear, a building permit is required once the garage exceeds Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF. square feet.
- ◦Benton serves Homestead, Owen, Walkersville and Hebardville and other communities around Blackshear.
- ◦The current local setback for a metal garage is The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number..
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on which ASCE 7/IBC edition Pierce County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
138
As of 2026 · Source |
Permits & Setbacks in Pierce County
The permit question for a Blackshear metal garage comes down to one number from Pierce County Planning & Codes Department: Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF. square feet. Stay under it and skip the full permit process; either way, keep the The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number. setback in mind before you pick a spot.
Delivery to Blackshear
Metal garage delivery to Blackshear can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Pierce County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Pierce County Planning & Codes Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How close can my metal garage be to the property line?
The current setback in Blackshear is The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number., although you should confirm the requirement for your particular property with Pierce County Planning & Codes Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Blackshear?
Benton Metal Depot's Statesboro location is approximately 91.4 miles from Blackshear. The company serves residents throughout Pierce, including communities such as Homestead, Owen, Walkersville and Hebardville. Current delivery time for a metal garage to the Blackshear area is about 1 to 2 weeks.
How long does it take to get a metal garage delivered to Blackshear?
Current delivery time to Blackshear is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Blackshear before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Blackshear, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Pierce County Planning & Codes Department has requirements that can affect garage placement, including a current setback of The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
Blackshear, Pierce County — At a Glance
- Permit Authority Name
- Pierce County Planning & Codes Department
- Permit Authority Url
- https://piercecountyga.gov/building-permits/
- Permit Threshold Sqft
- Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF.
- Setback Feet Side Rear
- The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.
- Wind Load Zone
- Southeast Georgia coastal plain — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on which ASCE 7/IBC edition Pierce County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 91.4
- Drive Minutes
- 138
- Nearby Towns
- Homestead, Owen, Walkersville, Hebardville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Blackshear and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Blackshear?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://piercecountyga.gov/contact-planning-and-codes/ (2026)
- https://piercecountyga.gov/building-permits/ (2026)
- https://piercecountyga.gov/building-permits/ and https://piercecountyga.gov/ZONING-GLAND-USE-ORDINANCE.pdf (2026)
- https://piercecountyga.gov/ZONING-GLAND-USE-ORDINANCE.pdf (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Pierce County is inland (~40-50 miles from the Atlantic) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
