Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Patterson? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Pierce, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Benton serves Trudie, Aspinwall, Otter Creek and Offerman and other communities around Patterson.
- ◦In Patterson, a building permit is required once the garage exceeds Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF. square feet.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number..
At a Glance
| Permit threshold |
Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on which ASCE 7/IBC edition Pierce County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
131
As of 2026 · Source |
Permits & Setbacks in Pierce County
Before a metal garage goes up in Patterson, check with Pierce County Planning & Codes Department — Pierce's cutoff for requiring a building permit is Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF. square feet. Below that, you still need to clear the The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number. setback from your property line.
Delivery to Patterson
The current estimate for getting a metal garage to Patterson is 1 to 2 weeks. The area is about 86.5 miles (131 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Pierce County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Patterson before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Patterson?
Current delivery time to Patterson is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Pierce County Planning & Codes Department has requirements that can affect garage placement, including a current setback of The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How far is Benton Metal Depot from Patterson?
Benton Metal Depot's Statesboro location is approximately 86.5 miles from Patterson. The company serves residents throughout Pierce, including communities such as Trudie, Aspinwall, Otter Creek and Offerman. Current delivery time for a metal garage to the Patterson area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Patterson is The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number., although you should confirm the requirement for your particular property with Pierce County Planning & Codes Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
Patterson, Pierce County — At a Glance
- Permit Authority Name
- Pierce County Planning & Codes Department
- Permit Authority Url
- https://piercecountyga.gov/building-permits/
- Permit Threshold Sqft
- Not found. No explicit sqft exemption is published on the county's Building Permits page. Needs direct confirmation with Pierce County Planning & Codes (912-449-2022) or a manual review of the county's Zoning/Land Use Ordinance PDF.
- Setback Feet Side Rear
- The county's Zoning/Land Use Ordinance states accessory buildings/uses must comply with front, side, and rear yard requirements set per-district in a dimensional table, but specific numeric setbacks could not be extracted from the ordinance PDF in this research pass. Verify against the primary PDF before publishing a specific number.
- Wind Load Zone
- Southeast Georgia coastal plain — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on which ASCE 7/IBC edition Pierce County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 86.5
- Drive Minutes
- 131
- Nearby Towns
- Trudie, Aspinwall, Otter Creek, Offerman
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Patterson, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Patterson?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://piercecountyga.gov/contact-planning-and-codes/ (2026)
- https://piercecountyga.gov/building-permits/ (2026)
- https://piercecountyga.gov/building-permits/ and https://piercecountyga.gov/ZONING-GLAND-USE-ORDINANCE.pdf (2026)
- https://piercecountyga.gov/ZONING-GLAND-USE-ORDINANCE.pdf (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Pierce County is inland (~40-50 miles from the Atlantic) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
