Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Millhaven can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Screven and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Delivery to Millhaven is currently estimated at 1 to 2 weeks.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Benton Metal Depot is approximately 26.3 miles from Millhaven.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
At a Glance
| Permit threshold |
Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.
As of 2026 · Source |
| Wind load zone |
Inland east-central Georgia — roughly 105-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
35
As of 2026 · Source |
Permits & Setbacks in Screven County
Screven treats a metal garage like any other accessory structure: under Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number. square feet, Screven County Planning and Zoning Department typically doesn't require a full permit, but the Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed. setback rule still governs where it can sit on the lot.
Delivery to Millhaven
Residents in Millhaven are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 26.3 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Screven County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Do I need a permit for a metal garage in Millhaven?
That depends on the garage and the requirements of Screven County Planning and Zoning Department. The current rule requires a permit once the garage exceeds Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Screven County Planning and Zoning Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Millhaven, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Screven County Planning and Zoning Department has requirements that can affect garage placement, including a current setback of Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
How close can my metal garage be to the property line?
The current setback in Millhaven is Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed., although you should confirm the requirement for your particular property with Screven County Planning and Zoning Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
Millhaven, Screven County — At a Glance
- Permit Authority Name
- Screven County Planning and Zoning Department
- Permit Authority Url
- https://www.screvencountyboc.com/planning-zoning
- Permit Threshold Sqft
- Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number.
- Setback Feet Side Rear
- Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.
- Wind Load Zone
- Inland east-central Georgia — roughly 105-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 26.3
- Drive Minutes
- 35
- Nearby Towns
- Brier Creek Landing, Dover, Woodcliff, Burtons Ferry Landing
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Millhaven and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Millhaven?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.screvencountyboc.com/planning-zoning (2026)
- https://www.zoneomics.com/code/screven-county-unincorporated-GA/chapter_13 — verify against the primary ordinance at https://library.municode.com/GA/Screven_County/codes/Code_of_Ordinances (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Screven County is well inland (east-central Georgia, on the Savannah River but far from the coast) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
