Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Ogeechee and across Screven, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Ogeechee is currently estimated at 1 to 2 weeks.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 26.3 miles from Ogeechee.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.
As of 2026 · Source |
| Wind load zone |
Inland east-central Georgia — roughly 105-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
35
As of 2026 · Source |
Permits & Setbacks in Screven County
The permit question for a Ogeechee metal garage comes down to one number from Screven County Planning and Zoning Department: Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number. square feet. Stay under it and skip the full permit process; either way, keep the Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed. setback in mind before you pick a spot.
Delivery to Ogeechee
Residents in Ogeechee are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 26.3 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Screven County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Screven County Planning and Zoning Department has requirements that can affect garage placement, including a current setback of Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How long does it take to get a metal garage delivered to Ogeechee?
Current delivery time to Ogeechee is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Ogeechee before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How close can my metal garage be to the property line?
The current setback in Ogeechee is Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed., although you should confirm the requirement for your particular property with Screven County Planning and Zoning Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Ogeechee?
Benton Metal Depot's Statesboro location is approximately 26.3 miles from Ogeechee. The company serves residents throughout Screven, including communities such as Brier Creek Landing, Dover, Woodcliff and Burtons Ferry Landing. Current delivery time for a metal garage to the Ogeechee area is about 1 to 2 weeks.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Ogeechee, Screven County — At a Glance
- Permit Authority Name
- Screven County Planning and Zoning Department
- Permit Authority Url
- https://www.screvencountyboc.com/planning-zoning
- Permit Threshold Sqft
- Not found. No sqft-based permit exemption was located on the county site. Contact the Screven County Zoning Office (912-564-2951) to confirm before publishing a number.
- Setback Feet Side Rear
- Accessory buildings not attached to the principal building must be located at least 12 ft from the principal building, and detached accessory structures must be located in the rear yard (not permitted in front or side yards), per a secondary summary of the Screven County zoning ordinance. This should be verified against the primary Municode text before publishing specific side/rear property-line setback distances, which were not independently confirmed.
- Wind Load Zone
- Inland east-central Georgia — roughly 105-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 26.3
- Drive Minutes
- 35
- Nearby Towns
- Brier Creek Landing, Dover, Woodcliff, Burtons Ferry Landing
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Ogeechee and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Ogeechee?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.screvencountyboc.com/planning-zoning (2026)
- https://www.zoneomics.com/code/screven-county-unincorporated-GA/chapter_13 — verify against the primary ordinance at https://library.municode.com/GA/Screven_County/codes/Code_of_Ordinances (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Screven County is well inland (east-central Georgia, on the Savannah River but far from the coast) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
