Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Gardi and across Wayne, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Delivery to Gardi is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton Metal Depot is approximately 76.8 miles from Gardi.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦The current local setback for a metal garage is Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning..
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain (Wayne County is roughly 35-45 miles from the Atlantic) — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
113
As of 2026 · Source |
Permits & Setbacks in Wayne County
Wayne treats a metal garage like any other accessory structure: under 200 square feet, Wayne County Building Inspections Department typically doesn't require a full permit, but the Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning. setback rule still governs where it can sit on the lot.
Delivery to Gardi
Residents in Gardi are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 76.8 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Wayne County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Gardi, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Do I need a permit for a metal garage in Gardi?
That depends on the garage and the requirements of Wayne County Building Inspections Department. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Wayne County Building Inspections Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from Gardi?
Benton Metal Depot's Statesboro location is approximately 76.8 miles from Gardi. The company serves residents throughout Wayne, including communities such as Lower Sansavilla, Slover, Broadhurst and Odessa. Current delivery time for a metal garage to the Gardi area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Gardi is Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning., although you should confirm the requirement for your particular property with Wayne County Building Inspections Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Gardi, Wayne County — At a Glance
- Permit Authority Name
- Wayne County Building Inspections Department
- Permit Authority Url
- https://www.waynecountyga.us/department/division.php?structureid=42
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning.
- Wind Load Zone
- Southeast Georgia coastal plain (Wayne County is roughly 35-45 miles from the Atlantic) — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 76.8
- Drive Minutes
- 113
- Nearby Towns
- Lower Sansavilla, Slover, Broadhurst, Odessa
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Gardi and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Gardi?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.waynecountyga.us/department/division.php?structureid=42 (2026)
- https://www.waynecountyga.us/department/division.php?structureid=42 ("Accessory structures such as tool or storage sheds; play houses or structures with similar functions that do not exceed 200 sq ft do not require a permit") (2026)
- https://library.municode.com/ga/wayne_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH8BUBURE (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Wayne County is inland relative to the immediate coastline and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
