Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Manningtown? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Wayne, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning..
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton serves Gardi, Lower Sansavilla, Slover and Broadhurst and other communities around Manningtown.
- ◦In Manningtown, a building permit is required once the garage exceeds 200 square feet.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain (Wayne County is roughly 35-45 miles from the Atlantic) — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
113
As of 2026 · Source |
Permits & Setbacks in Wayne County
Before a metal garage goes up in Manningtown, check with Wayne County Building Inspections Department — Wayne's cutoff for requiring a building permit is 200 square feet. Below that, you still need to clear the Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning. setback from your property line.
Delivery to Manningtown
The current estimate for getting a metal garage to Manningtown is 1 to 2 weeks. The area is about 76.8 miles (113 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Wayne County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Wayne County Building Inspections Department has requirements that can affect garage placement, including a current setback of Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Manningtown?
That depends on the garage and the requirements of Wayne County Building Inspections Department. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Manningtown before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Definitions
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
Manningtown, Wayne County — At a Glance
- Permit Authority Name
- Wayne County Building Inspections Department
- Permit Authority Url
- https://www.waynecountyga.us/department/division.php?structureid=42
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not found. No specific numeric side/rear setback figures for accessory structures were located on the county site or extractable from the Code of Ordinances in this pass. Needs direct confirmation with Wayne County Building Inspections/Planning.
- Wind Load Zone
- Southeast Georgia coastal plain (Wayne County is roughly 35-45 miles from the Atlantic) — roughly 120-135 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 76.8
- Drive Minutes
- 113
- Nearby Towns
- Gardi, Lower Sansavilla, Slover, Broadhurst
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Manningtown, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Manningtown?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.waynecountyga.us/department/division.php?structureid=42 (2026)
- https://www.waynecountyga.us/department/division.php?structureid=42 ("Accessory structures such as tool or storage sheds; play houses or structures with similar functions that do not exceed 200 sq ft do not require a permit") (2026)
- https://library.municode.com/ga/wayne_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH8BUBURE (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Wayne County is inland relative to the immediate coastline and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
