Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Barton can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Allendale and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Barton is currently estimated at 1 to 2 weeks.
- ◦Benton Metal Depot is approximately 61.7 miles from Barton.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
Not found for the county specifically. One secondary source notes that in Allendale County, a carport under 200 sq ft may only need a zoning permit while a building permit is required above 200 sq ft, but this was not confirmed against a primary county ordinance. Needs direct confirmation.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found for unincorporated Allendale County. The Town of Allendale has its own Zoning and Land Management Ordinance (2013) with setback tables, but that is Town-specific and not confirmed to apply county-wide. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina — roughly 120-130 mph (ASCE 7, Exposure C). NOT a verified figure; Allendale County is well inland (bordering Georgia along the Savannah River) and the exact design wind speed depends on the ASCE 7 edition adopted and must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
80
As of 2026 · Source |
Permits & Setbacks in Allendale County
Before a metal garage goes up in Barton, check with Not clearly identified for the unincorporated county — search results only surface the Town of Allendale's Building/Zoning/Business License office. No distinct "Allendale County" (vs. Town of Allendale) building department page was found; the county may share services via the Lowcountry Council of Governments. Needs direct confirmation. — Allendale's cutoff for requiring a building permit is Not found for the county specifically. One secondary source notes that in Allendale County, a carport under 200 sq ft may only need a zoning permit while a building permit is required above 200 sq ft, but this was not confirmed against a primary county ordinance. Needs direct confirmation. square feet. Below that, you still need to clear the Not found for unincorporated Allendale County. The Town of Allendale has its own Zoning and Land Management Ordinance (2013) with setback tables, but that is Town-specific and not confirmed to apply county-wide. Needs direct confirmation. setback from your property line.
Delivery to Barton
Residents in Barton are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 61.7 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Allendale County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Barton, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How close can my metal garage be to the property line?
The current setback in Barton is Not found for unincorporated Allendale County. The Town of Allendale has its own Zoning and Land Management Ordinance (2013) with setback tables, but that is Town-specific and not confirmed to apply county-wide. Needs direct confirmation., although you should confirm the requirement for your particular property with Not clearly identified for the unincorporated county — search results only surface the Town of Allendale's Building/Zoning/Business License office. No distinct "Allendale County" (vs. Town of Allendale) building department page was found; the county may share services via the Lowcountry Council of Governments. Needs direct confirmation.. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Barton?
Benton Metal Depot's Statesboro location is approximately 61.7 miles from Barton. The company serves residents throughout Allendale, including communities such as Lopers Crossroads, Jennys, Rouse and Sycamore. Current delivery time for a metal garage to the Barton area is about 1 to 2 weeks.
How long does it take to get a metal garage delivered to Barton?
Current delivery time to Barton is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Barton before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Not clearly identified for the unincorporated county — search results only surface the Town of Allendale's Building/Zoning/Business License office. No distinct "Allendale County" (vs. Town of Allendale) building department page was found; the county may share services via the Lowcountry Council of Governments. Needs direct confirmation.. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
Barton, Allendale County — At a Glance
- Permit Authority Name
- Not clearly identified for the unincorporated county — search results only surface the Town of Allendale's Building/Zoning/Business License office. No distinct "Allendale County" (vs. Town of Allendale) building department page was found; the county may share services via the Lowcountry Council of Governments. Needs direct confirmation.
- Permit Authority Url
- https://www.allendalecounty.com/ (county homepage; no dedicated building/permitting subpage located) — https://townofallendale.sc.gov/building-zoning-and-business-license is the closest confirmed permitting office found, but it is Town-level, not county-level
- Permit Threshold Sqft
- Not found for the county specifically. One secondary source notes that in Allendale County, a carport under 200 sq ft may only need a zoning permit while a building permit is required above 200 sq ft, but this was not confirmed against a primary county ordinance. Needs direct confirmation.
- Setback Feet Side Rear
- Not found for unincorporated Allendale County. The Town of Allendale has its own Zoning and Land Management Ordinance (2013) with setback tables, but that is Town-specific and not confirmed to apply county-wide. Needs direct confirmation.
- Wind Load Zone
- Inland South Carolina — roughly 120-130 mph (ASCE 7, Exposure C). NOT a verified figure; Allendale County is well inland (bordering Georgia along the Savannah River) and the exact design wind speed depends on the ASCE 7 edition adopted and must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 61.7
- Drive Minutes
- 80
- Nearby Towns
- Lopers Crossroads, Jennys, Rouse, Sycamore
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Barton and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Barton?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://townofallendale.sc.gov/building-zoning-and-business-license (Town-level, may not cover unincorporated county); https://www.allendalecounty.com/ (county homepage) (2026)
- https://www.allendalecounty.com/ and https://townofallendale.sc.gov/building-zoning-and-business-license (2026)
- Secondary aggregator source only (coldspringmetal.com); no primary Allendale County ordinance located (2026)
- https://townofallendale.sc.gov/sites/townofallendale/files/Documents/Allendale_ZO_FINAL(9-10-13).pdf (Town-level only) (2026)
- General ASCE 7 inland-South-Carolina range (aggregated secondary sources, e.g. windload.solutions) — no county-specific or primary map source found (2026)
- Given/client spec — Allendale County, SC is inland (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
