Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Jennys, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Allendale and the surrounding area.
Key Points
- ◦Delivery to Jennys is currently estimated at 1 to 2 weeks.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 61.7 miles from Jennys.
At a Glance
| Permit threshold |
Not found for the county specifically. One secondary source notes that in Allendale County, a carport under 200 sq ft may only need a zoning permit while a building permit is required above 200 sq ft, but this was not confirmed against a primary county ordinance. Needs direct confirmation.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found for unincorporated Allendale County. The Town of Allendale has its own Zoning and Land Management Ordinance (2013) with setback tables, but that is Town-specific and not confirmed to apply county-wide. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina — roughly 120-130 mph (ASCE 7, Exposure C). NOT a verified figure; Allendale County is well inland (bordering Georgia along the Savannah River) and the exact design wind speed depends on the ASCE 7 edition adopted and must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
80
As of 2026 · Source |
Permits & Setbacks in Allendale County
Allendale treats a metal garage like any other accessory structure: under Not found for the county specifically. One secondary source notes that in Allendale County, a carport under 200 sq ft may only need a zoning permit while a building permit is required above 200 sq ft, but this was not confirmed against a primary county ordinance. Needs direct confirmation. square feet, Not clearly identified for the unincorporated county — search results only surface the Town of Allendale's Building/Zoning/Business License office. No distinct "Allendale County" (vs. Town of Allendale) building department page was found; the county may share services via the Lowcountry Council of Governments. Needs direct confirmation. typically doesn't require a full permit, but the Not found for unincorporated Allendale County. The Town of Allendale has its own Zoning and Land Management Ordinance (2013) with setback tables, but that is Town-specific and not confirmed to apply county-wide. Needs direct confirmation. setback rule still governs where it can sit on the lot.
Delivery to Jennys
The current estimate for getting a metal garage to Jennys is 1 to 2 weeks. The area is about 61.7 miles (80 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Allendale County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Do I need a permit for a metal garage in Jennys?
That depends on the garage and the requirements of Not clearly identified for the unincorporated county — search results only surface the Town of Allendale's Building/Zoning/Business License office. No distinct "Allendale County" (vs. Town of Allendale) building department page was found; the county may share services via the Lowcountry Council of Governments. Needs direct confirmation.. The current rule requires a permit once the garage exceeds Not found for the county specifically. One secondary source notes that in Allendale County, a carport under 200 sq ft may only need a zoning permit while a building permit is required above 200 sq ft, but this was not confirmed against a primary county ordinance. Needs direct confirmation. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Not clearly identified for the unincorporated county — search results only surface the Town of Allendale's Building/Zoning/Business License office. No distinct "Allendale County" (vs. Town of Allendale) building department page was found; the county may share services via the Lowcountry Council of Governments. Needs direct confirmation. has requirements that can affect garage placement, including a current setback of Not found for unincorporated Allendale County. The Town of Allendale has its own Zoning and Land Management Ordinance (2013) with setback tables, but that is Town-specific and not confirmed to apply county-wide. Needs direct confirmation.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Jennys, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Definitions
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Jennys, Allendale County — At a Glance
- Permit Authority Name
- Not clearly identified for the unincorporated county — search results only surface the Town of Allendale's Building/Zoning/Business License office. No distinct "Allendale County" (vs. Town of Allendale) building department page was found; the county may share services via the Lowcountry Council of Governments. Needs direct confirmation.
- Permit Authority Url
- https://www.allendalecounty.com/ (county homepage; no dedicated building/permitting subpage located) — https://townofallendale.sc.gov/building-zoning-and-business-license is the closest confirmed permitting office found, but it is Town-level, not county-level
- Permit Threshold Sqft
- Not found for the county specifically. One secondary source notes that in Allendale County, a carport under 200 sq ft may only need a zoning permit while a building permit is required above 200 sq ft, but this was not confirmed against a primary county ordinance. Needs direct confirmation.
- Setback Feet Side Rear
- Not found for unincorporated Allendale County. The Town of Allendale has its own Zoning and Land Management Ordinance (2013) with setback tables, but that is Town-specific and not confirmed to apply county-wide. Needs direct confirmation.
- Wind Load Zone
- Inland South Carolina — roughly 120-130 mph (ASCE 7, Exposure C). NOT a verified figure; Allendale County is well inland (bordering Georgia along the Savannah River) and the exact design wind speed depends on the ASCE 7 edition adopted and must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 61.7
- Drive Minutes
- 80
- Nearby Towns
- Lopers Crossroads, Barton, Rouse, Sycamore
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Jennys, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Jennys?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://townofallendale.sc.gov/building-zoning-and-business-license (Town-level, may not cover unincorporated county); https://www.allendalecounty.com/ (county homepage) (2026)
- https://www.allendalecounty.com/ and https://townofallendale.sc.gov/building-zoning-and-business-license (2026)
- Secondary aggregator source only (coldspringmetal.com); no primary Allendale County ordinance located (2026)
- https://townofallendale.sc.gov/sites/townofallendale/files/Documents/Allendale_ZO_FINAL(9-10-13).pdf (Town-level only) (2026)
- General ASCE 7 inland-South-Carolina range (aggregated secondary sources, e.g. windload.solutions) — no county-specific or primary map source found (2026)
- Given/client spec — Allendale County, SC is inland (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
