Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Blake, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Colleton.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Blake is currently estimated at 1 to 2 weeks.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 97.9 miles from Blake.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not found — Colleton County FAQ confirms zoning permits are required for accessory structures like "sheds, fences, barns" without stating a sqft exemption; both a building permit and a zoning permit are typically needed. Needs direct confirmation (843-549-1709).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts.
As of 2026 · Source |
| Wind load zone |
Colleton County is classified in secondary sources as a Coastal High-Hazard Wind Zone (>130 mph, ASCE 7-16/7-22, Risk Category II) within roughly 1 mile of the mean high-water line, tapering toward inland-SC levels (~115-120 mph) further from the coast/tidal rivers. NOT verified against a primary county map; must be confirmed with a SC-licensed engineer or the county building official, especially given how much Colleton's interior extends from the ACE Basin coastline.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
119
As of 2026 · Source |
Permits & Setbacks in Colleton County
Before a metal garage goes up in Blake, check with Colleton County Planning and Development Department (Building Code Administration) — Colleton's cutoff for requiring a building permit is Not found — Colleton County FAQ confirms zoning permits are required for accessory structures like "sheds, fences, barns" without stating a sqft exemption; both a building permit and a zoning permit are typically needed. Needs direct confirmation (843-549-1709). square feet. Below that, you still need to clear the Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts. setback from your property line.
Delivery to Blake
Metal garage delivery to Blake can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Colleton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Colleton County Planning and Development Department (Building Code Administration) has requirements that can affect garage placement, including a current setback of Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Blake?
That depends on the garage and the requirements of Colleton County Planning and Development Department (Building Code Administration). The current rule requires a permit once the garage exceeds Not found — Colleton County FAQ confirms zoning permits are required for accessory structures like "sheds, fences, barns" without stating a sqft exemption; both a building permit and a zoning permit are typically needed. Needs direct confirmation (843-549-1709). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Colleton County Planning and Development Department (Building Code Administration). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Definitions
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
Blake, Colleton County — At a Glance
- Permit Authority Name
- Colleton County Planning and Development Department (Building Code Administration)
- Permit Authority Url
- https://www.colletoncounty.org/planning-development/building-code-administration
- Permit Threshold Sqft
- Not found — Colleton County FAQ confirms zoning permits are required for accessory structures like "sheds, fences, barns" without stating a sqft exemption; both a building permit and a zoning permit are typically needed. Needs direct confirmation (843-549-1709).
- Setback Feet Side Rear
- Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts.
- Wind Load Zone
- Colleton County is classified in secondary sources as a Coastal High-Hazard Wind Zone (>130 mph, ASCE 7-16/7-22, Risk Category II) within roughly 1 mile of the mean high-water line, tapering toward inland-SC levels (~115-120 mph) further from the coast/tidal rivers. NOT verified against a primary county map; must be confirmed with a SC-licensed engineer or the county building official, especially given how much Colleton's interior extends from the ACE Basin coastline.
- Coastal
- 1
- Drive Miles
- 97.9
- Drive Minutes
- 119
- Nearby Towns
- Hendersonville, Pocotaligo, McPhersonville, Brewton
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Blake and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Blake?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.colletoncounty.org/planning-development/building-code-administration (2026)
- https://www.colletoncounty.org/faq/when-do-i-need-zoning-permit (2026)
- Colleton County Code of Ordinances, Title 14.08 (Zoning), https://www.colletoncounty.org/sites/default/files/uploads/planning_dev/2022%20Ordinance%20Update/2022-update-zoning-ordinance.pdf — needs direct lookup of the district yard table (2026)
- Aggregated from windload.solutions and similar secondary sources — no primary Colleton County wind map found (2026)
- Given/client spec — Colleton County is a coastal South Carolina county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Colleton County
See the Colleton County hub for metal garages
