Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Colleton? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Colleton, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦In Colleton, a building permit is required once the garage exceeds Not found — Colleton County FAQ confirms zoning permits are required for accessory structures like "sheds, fences, barns" without stating a sqft exemption; both a building permit and a zoning permit are typically needed. Needs direct confirmation (843-549-1709). square feet.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Benton serves Sniders Crossroads, Bells Crossroads, Hudsons Mill and Padgetts and other communities around Colleton.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦The current local setback for a metal garage is Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts..
At a Glance
| Permit threshold |
Not found — Colleton County FAQ confirms zoning permits are required for accessory structures like "sheds, fences, barns" without stating a sqft exemption; both a building permit and a zoning permit are typically needed. Needs direct confirmation (843-549-1709).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts.
As of 2026 · Source |
| Wind load zone |
Colleton County is classified in secondary sources as a Coastal High-Hazard Wind Zone (>130 mph, ASCE 7-16/7-22, Risk Category II) within roughly 1 mile of the mean high-water line, tapering toward inland-SC levels (~115-120 mph) further from the coast/tidal rivers. NOT verified against a primary county map; must be confirmed with a SC-licensed engineer or the county building official, especially given how much Colleton's interior extends from the ACE Basin coastline.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
123
As of 2026 · Source |
Permits & Setbacks in Colleton County
Before a metal garage goes up in Colleton, check with Colleton County Planning and Development Department (Building Code Administration) — Colleton's cutoff for requiring a building permit is Not found — Colleton County FAQ confirms zoning permits are required for accessory structures like "sheds, fences, barns" without stating a sqft exemption; both a building permit and a zoning permit are typically needed. Needs direct confirmation (843-549-1709). square feet. Below that, you still need to clear the Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts. setback from your property line.
Delivery to Colleton
The current estimate for getting a metal garage to Colleton is 1 to 2 weeks. The area is about 87.8 miles (123 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Colleton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Colleton, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How far is Benton Metal Depot from Colleton?
Benton Metal Depot's Statesboro location is approximately 87.8 miles from Colleton. The company serves residents throughout Colleton, including communities such as Sniders Crossroads, Bells Crossroads, Hudsons Mill and Padgetts. Current delivery time for a metal garage to the Colleton area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Colleton is Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts., although you should confirm the requirement for your particular property with Colleton County Planning and Development Department (Building Code Administration). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Colleton before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Colleton?
Current delivery time to Colleton is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Colleton County Planning and Development Department (Building Code Administration). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Colleton, Colleton County — At a Glance
- Permit Authority Name
- Colleton County Planning and Development Department (Building Code Administration)
- Permit Authority Url
- https://www.colletoncounty.org/planning-development/building-code-administration
- Permit Threshold Sqft
- Not found — Colleton County FAQ confirms zoning permits are required for accessory structures like "sheds, fences, barns" without stating a sqft exemption; both a building permit and a zoning permit are typically needed. Needs direct confirmation (843-549-1709).
- Setback Feet Side Rear
- Accessory buildings must be separated from the principal structure or other accessory structures by at least 5 ft; district-specific side/rear property-line setback figures for accessory structures were not retrieved from available excerpts.
- Wind Load Zone
- Colleton County is classified in secondary sources as a Coastal High-Hazard Wind Zone (>130 mph, ASCE 7-16/7-22, Risk Category II) within roughly 1 mile of the mean high-water line, tapering toward inland-SC levels (~115-120 mph) further from the coast/tidal rivers. NOT verified against a primary county map; must be confirmed with a SC-licensed engineer or the county building official, especially given how much Colleton's interior extends from the ACE Basin coastline.
- Coastal
- 1
- Drive Miles
- 87.8
- Drive Minutes
- 123
- Nearby Towns
- Sniders Crossroads, Bells Crossroads, Hudsons Mill, Padgetts
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Colleton and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Colleton?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.colletoncounty.org/planning-development/building-code-administration (2026)
- https://www.colletoncounty.org/faq/when-do-i-need-zoning-permit (2026)
- Colleton County Code of Ordinances, Title 14.08 (Zoning), https://www.colletoncounty.org/sites/default/files/uploads/planning_dev/2022%20Ordinance%20Update/2022-update-zoning-ordinance.pdf — needs direct lookup of the district yard table (2026)
- Aggregated from windload.solutions and similar secondary sources — no primary Colleton County wind map found (2026)
- Given/client spec — Colleton County is a coastal South Carolina county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Colleton County
See the Colleton County hub for metal garages
