Reviewed by the Benton Metal Depot team · Updated
For some residents in Davis, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Appling, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Davis is currently estimated at 1 to 2 weeks.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 75.2 miles from Davis.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Appling County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
100
As of 2026 · Source |
Permits & Setbacks in Appling County
Before a metal garage goes up in Davis, check with Appling County Planning & Zoning (under the Board of Commissioners) — Appling's cutoff for requiring a building permit is Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning. square feet. Below that, you still need to clear the Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation. setback from your property line.
Delivery to Davis
Metal garage delivery to Davis can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Appling County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How close can my metal garage be to the property line?
The current setback in Davis is Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation., although you should confirm the requirement for your particular property with Appling County Planning & Zoning (under the Board of Commissioners). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Davis?
Benton Metal Depot's Statesboro location is approximately 75.2 miles from Davis. The company serves residents throughout Appling, including communities such as Eason Bluff, Spring Branch, Zion and Falling Rocks. Current delivery time for a metal garage to the Davis area is about 1 to 2 weeks.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Appling County Planning & Zoning (under the Board of Commissioners) has requirements that can affect garage placement, including a current setback of Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How long does it take to get a metal garage delivered to Davis?
Current delivery time to Davis is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Davis before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Definitions
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
Davis, Appling County — At a Glance
- Permit Authority Name
- Appling County Planning & Zoning (under the Board of Commissioners)
- Permit Authority Url
- https://applingcountyga.org/?page_id=155
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning.
- Setback Feet Side Rear
- Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Appling County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 75.2
- Drive Minutes
- 100
- Nearby Towns
- Eason Bluff, Spring Branch, Zion, Falling Rocks
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Davis, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Davis?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://applingcountyga.org/?page_id=155 (2026)
- No primary source found; https://applingcountyga.org/?page_id=155 does not publish a threshold (2026)
- No primary source found (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Appling County is inland (southeast GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
