Reviewed by the Benton Metal Depot team · Updated
For some residents in Prentiss, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Appling, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Benton Metal Depot is approximately 75.2 miles from Prentiss.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Delivery to Prentiss is currently estimated at 1 to 2 weeks.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Appling County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
100
As of 2026 · Source |
Permits & Setbacks in Appling County
The permit question for a Prentiss metal garage comes down to one number from Appling County Planning & Zoning (under the Board of Commissioners): Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning. square feet. Stay under it and skip the full permit process; either way, keep the Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation. setback in mind before you pick a spot.
Delivery to Prentiss
Residents in Prentiss are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 75.2 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Appling County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Appling County Planning & Zoning (under the Board of Commissioners) has requirements that can affect garage placement, including a current setback of Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Prentiss?
That depends on the garage and the requirements of Appling County Planning & Zoning (under the Board of Commissioners). The current rule requires a permit once the garage exceeds Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Prentiss before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Prentiss, Appling County — At a Glance
- Permit Authority Name
- Appling County Planning & Zoning (under the Board of Commissioners)
- Permit Authority Url
- https://applingcountyga.org/?page_id=155
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning.
- Setback Feet Side Rear
- Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Appling County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 75.2
- Drive Minutes
- 100
- Nearby Towns
- Eason Bluff, Spring Branch, Zion, Falling Rocks
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Prentiss and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Prentiss?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://applingcountyga.org/?page_id=155 (2026)
- No primary source found; https://applingcountyga.org/?page_id=155 does not publish a threshold (2026)
- No primary source found (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Appling County is inland (southeast GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
