Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Graham can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Appling and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Benton serves Eason Bluff, Spring Branch, Zion and Falling Rocks and other communities around Graham.
- ◦In Graham, a building permit is required once the garage exceeds Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning. square feet.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Appling County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
100
As of 2026 · Source |
Permits & Setbacks in Appling County
The permit question for a Graham metal garage comes down to one number from Appling County Planning & Zoning (under the Board of Commissioners): Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning. square feet. Stay under it and skip the full permit process; either way, keep the Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation. setback in mind before you pick a spot.
Delivery to Graham
Metal garage delivery to Graham can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Appling County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Graham, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How long does it take to get a metal garage delivered to Graham?
Current delivery time to Graham is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Graham before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How close can my metal garage be to the property line?
The current setback in Graham is Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation., although you should confirm the requirement for your particular property with Appling County Planning & Zoning (under the Board of Commissioners). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Graham?
Benton Metal Depot's Statesboro location is approximately 75.2 miles from Graham. The company serves residents throughout Appling, including communities such as Eason Bluff, Spring Branch, Zion and Falling Rocks. Current delivery time for a metal garage to the Graham area is about 1 to 2 weeks.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Appling County Planning & Zoning (under the Board of Commissioners). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
Graham, Appling County — At a Glance
- Permit Authority Name
- Appling County Planning & Zoning (under the Board of Commissioners)
- Permit Authority Url
- https://applingcountyga.org/?page_id=155
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site or in secondary sources. Needs direct confirmation with Appling County Planning & Zoning.
- Setback Feet Side Rear
- Not found — no published zoning ordinance setback table located online for Appling County via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Appling County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 75.2
- Drive Minutes
- 100
- Nearby Towns
- Eason Bluff, Spring Branch, Zion, Falling Rocks
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Graham and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Graham?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://applingcountyga.org/?page_id=155 (2026)
- No primary source found; https://applingcountyga.org/?page_id=155 does not publish a threshold (2026)
- No primary source found (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Appling County is inland (southeast GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
