Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Fendig? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Brantley, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Delivery to Fendig is currently estimated at 1 to 2 weeks.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton Metal Depot is approximately 90.3 miles from Fendig.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.
As of 2026 · Source |
| Wind load zone |
Inland/near-coastal Georgia (Nahunta) — roughly 115-125 mph (ASCE 7, Exposure C); Brantley County sits just inland of the coastal GA counties (Camden/Glynn) so its mapped speed is likely somewhat lower than the ~130 mph coastal band but higher than deep-interior GA. NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
135
As of 2026 · Source |
Permits & Setbacks in Brantley County
The permit question for a Fendig metal garage comes down to one number from Brantley County Planning & Building Department: Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256). square feet. Stay under it and skip the full permit process; either way, keep the Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts. setback in mind before you pick a spot.
Delivery to Fendig
Current delivery time to Fendig is approximately 1 to 2 weeks. Benton also serves nearby communities including Hortense, O Neal, Needmore and Popwellville. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Brantley County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Fendig before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Fendig?
Current delivery time to Fendig is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Fendig, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Brantley County Planning & Building Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from Fendig?
Benton Metal Depot's Statesboro location is approximately 90.3 miles from Fendig. The company serves residents throughout Brantley, including communities such as Hortense, O Neal, Needmore and Popwellville. Current delivery time for a metal garage to the Fendig area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Fendig is Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts., although you should confirm the requirement for your particular property with Brantley County Planning & Building Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
Fendig, Brantley County — At a Glance
- Permit Authority Name
- Brantley County Planning & Building Department
- Permit Authority Url
- https://brantleycounty-ga.gov/planning--building
- Permit Threshold Sqft
- Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256).
- Setback Feet Side Rear
- Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.
- Wind Load Zone
- Inland/near-coastal Georgia (Nahunta) — roughly 115-125 mph (ASCE 7, Exposure C); Brantley County sits just inland of the coastal GA counties (Camden/Glynn) so its mapped speed is likely somewhat lower than the ~130 mph coastal band but higher than deep-interior GA. NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 90.3
- Drive Minutes
- 135
- Nearby Towns
- Hortense, O Neal, Needmore, Popwellville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Fendig and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Fendig?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://brantleycounty-ga.gov/planning--building (2026)
- Land Use Ordinance for Brantley County, Georgia (adopted 9/8/2016), https://www.sgrc.us/documents/localgovernmentservices/development/4ad60d41e5b8542a349de9376b720273.pdf — needs direct lookup of the district table (2026)
- General ASCE 7 range inferred from proximity to coastal Georgia counties (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Given/client spec — Brantley County is inland Georgia (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
