Metal Garages in Schlatterville 2026

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Schlatterville, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Brantley and the surrounding area.

Key Points

◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
◦Benton Metal Depot is approximately 104.3 miles from Schlatterville.
◦Doors, windows and other selections can change the final cost of a garage.
◦Get the final garage dimensions before completing permanent site work.
◦Delivery to Schlatterville is currently estimated at 1 to 2 weeks.

At a Glance

Permit threshold	Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256). As of 2026 · Source
Setback (side/rear)	Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts. As of 2026 · Source
Wind load zone	Inland/near-coastal Georgia (Nahunta) — roughly 115-125 mph (ASCE 7, Exposure C); Brantley County sits just inland of the coastal GA counties (Camden/Glynn) so its mapped speed is likely somewhat lower than the ~130 mph coastal band but higher than deep-interior GA. NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	158 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Brantley County

The permit question for a Schlatterville metal garage comes down to one number from Brantley County Planning & Building Department: Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256). square feet. Stay under it and skip the full permit process; either way, keep the Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts. setback in mind before you pick a spot.

Delivery to Schlatterville

Residents in Schlatterville are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 104.3 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.

Representative product photo — a Brantley County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Do I need a permit for a metal garage in Schlatterville?

That depends on the garage and the requirements of Brantley County Planning & Building Department. The current rule requires a permit once the garage exceeds Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. Brantley County Planning & Building Department has requirements that can affect garage placement, including a current setback of Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Schlatterville, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

Definitions

◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.
◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.

Schlatterville, Brantley County — At a Glance

Permit Authority Name: Brantley County Planning & Building Department
Permit Authority Url: https://brantleycounty-ga.gov/planning--building
Permit Threshold Sqft: Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256).
Setback Feet Side Rear: Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.
Wind Load Zone: Inland/near-coastal Georgia (Nahunta) — roughly 115-125 mph (ASCE 7, Exposure C); Brantley County sits just inland of the coastal GA counties (Camden/Glynn) so its mapped speed is likely somewhat lower than the ~130 mph coastal band but higher than deep-interior GA. NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
Coastal
Drive Miles: 104.3
Drive Minutes: 158
Nearby Towns: Hoboken, Prosperity, Hickox, Lulaton
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Schlatterville and throughout the region to help them choose a garage package that will work well with whatever they need.

Ready to talk through your metal garages project in Schlatterville?

Call (912) 489-5795

Sources

Other Cities We Serve in Brantley County

See the Brantley County hub for metal garages

Atkinson Big Oak Browntown Fendig Fort Mudge Hickox Hoboken Hortense Lulaton Nahunta Needmore Popwellville Prosperity Raybon Salter Schlatterville Trudie Waynesville

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Schlatterville, Brantley County, Georgia (2026)