Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Raybon can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Brantley and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 100 miles from Raybon.
- ◦Delivery to Raybon is currently estimated at 1 to 2 weeks.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.
As of 2026 · Source |
| Wind load zone |
Inland/near-coastal Georgia (Nahunta) — roughly 115-125 mph (ASCE 7, Exposure C); Brantley County sits just inland of the coastal GA counties (Camden/Glynn) so its mapped speed is likely somewhat lower than the ~130 mph coastal band but higher than deep-interior GA. NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
153
As of 2026 · Source |
Permits & Setbacks in Brantley County
Brantley treats a metal garage like any other accessory structure: under Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256). square feet, Brantley County Planning & Building Department typically doesn't require a full permit, but the Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts. setback rule still governs where it can sit on the lot.
Delivery to Raybon
Current delivery time to Raybon is approximately 1 to 2 weeks. Benton also serves nearby communities including Prosperity, Hickox, Lulaton and Nahunta. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Brantley County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Raybon?
That depends on the garage and the requirements of Brantley County Planning & Building Department. The current rule requires a permit once the garage exceeds Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Raybon, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Brantley County Planning & Building Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from Raybon?
Benton Metal Depot's Statesboro location is approximately 100 miles from Raybon. The company serves residents throughout Brantley, including communities such as Prosperity, Hickox, Lulaton and Nahunta. Current delivery time for a metal garage to the Raybon area is about 1 to 2 weeks.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
Raybon, Brantley County — At a Glance
- Permit Authority Name
- Brantley County Planning & Building Department
- Permit Authority Url
- https://brantleycounty-ga.gov/planning--building
- Permit Threshold Sqft
- Not found — the county publishes a permit fee structure for accessory structures ($0.25/sq ft or $75 minimum, whichever is greater) but no explicit sqft exemption threshold was located, implying a permit may be required regardless of size. Needs direct confirmation (912-462-8743 / 912-462-5256).
- Setback Feet Side Rear
- Per the Brantley County Land Use Ordinance (adopted 9/8/2016), accessory buildings/uses on non-residential lots must comply with the same front/side/rear yard requirements as the principal Land Use district in which they sit; specific footage figures by district were not retrieved from available excerpts.
- Wind Load Zone
- Inland/near-coastal Georgia (Nahunta) — roughly 115-125 mph (ASCE 7, Exposure C); Brantley County sits just inland of the coastal GA counties (Camden/Glynn) so its mapped speed is likely somewhat lower than the ~130 mph coastal band but higher than deep-interior GA. NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 100
- Drive Minutes
- 153
- Nearby Towns
- Prosperity, Hickox, Lulaton, Nahunta
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Raybon, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Raybon?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://brantleycounty-ga.gov/planning--building (2026)
- Land Use Ordinance for Brantley County, Georgia (adopted 9/8/2016), https://www.sgrc.us/documents/localgovernmentservices/development/4ad60d41e5b8542a349de9376b720273.pdf — needs direct lookup of the district table (2026)
- General ASCE 7 range inferred from proximity to coastal Georgia counties (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Given/client spec — Brantley County is inland Georgia (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
