Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Colon can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Clinch and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Delivery to Colon is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton Metal Depot is approximately 153.6 miles from Colon.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
228
As of 2026 · Source |
Permits & Setbacks in Clinch County
Before a metal garage goes up in Colon, check with Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices. — Clinch's cutoff for requiring a building permit is No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact. square feet. Below that, you still need to clear the Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county. setback from your property line.
Delivery to Colon
The current estimate for getting a metal garage to Colon is 1 to 2 weeks. The area is about 153.6 miles (228 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Clinch County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Colon, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Do I need a permit for a metal garage in Colon?
That depends on the garage and the requirements of Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices.. The current rule requires a permit once the garage exceeds No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices.. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How far is Benton Metal Depot from Colon?
Benton Metal Depot's Statesboro location is approximately 153.6 miles from Colon. The company serves residents throughout Clinch, including communities such as Edith, Ernest, Council and Fargo. Current delivery time for a metal garage to the Colon area is about 1 to 2 weeks.
Definitions
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
Colon, Clinch County — At a Glance
- Permit Authority Name
- Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices.
- Permit Authority Url
- https://clinchcountyga.gov/contact.html
- Permit Threshold Sqft
- No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 153.6
- Drive Minutes
- 228
- Nearby Towns
- Edith, Ernest, Council, Fargo
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Colon and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Colon?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://clinchcountyga.gov/contact.html (2026)
- Georgia adoption of 2024 IRC with GA Amendments (statewide baseline); no Clinch County-specific ordinance located online (2026)
- https://georgiaplanning.com/documents/atlas/GOMI_zoning.pdf (lists Clinch among counties with a zoning ordinance, but does not publish the ordinance text) (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Clinch County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Clinch County is deep inland South Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
