Metal Garages in Fivemile Still 2026

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

A garage doesn't have to be just a place to park the car. Property owners in Fivemile Still can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Clinch and can help you find the building depending on how the space will actually be used.

Key Points

◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
◦Check the permit and setback rules before deciding exactly where the garage will go.
◦The current local setback for a metal garage is Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county..
◦Benton serves Sirmans, Cutting, Cogdell and Traisville and other communities around Fivemile Still.
◦In Fivemile Still, a building permit is required once the garage exceeds No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact. square feet.

At a Glance

Permit threshold	No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact. As of 2026 · Source
Setback (side/rear)	Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county. As of 2026 · Source
Wind load zone	Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	189 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Clinch County

Clinch's permitting office, Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices., sets the accessory-structure line at No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact. square feet — build under that and you generally skip the full building-permit process, though a setback of Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.

Delivery to Fivemile Still

Metal garage delivery to Fivemile Still can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.

Representative product photo — a Clinch County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices. has requirements that can affect garage placement, including a current setback of Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Do I need a permit for a metal garage in Fivemile Still?

That depends on the garage and the requirements of Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices.. The current rule requires a permit once the garage exceeds No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Fivemile Still, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

Definitions

◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.

Fivemile Still, Clinch County — At a Glance

Permit Authority Name: Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices.
Permit Authority Url: https://clinchcountyga.gov/contact.html
Permit Threshold Sqft: No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact.
Setback Feet Side Rear: Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county.
Wind Load Zone: Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
Coastal
Drive Miles: 127.5
Drive Minutes: 189
Nearby Towns: Sirmans, Cutting, Cogdell, Traisville
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Fivemile Still, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.

Ready to talk through your metal garages project in Fivemile Still?

Call (912) 489-5795

Sources

Other Cities We Serve in Clinch County

See the Clinch County hub for metal garages

Argyle Cogdell Colon Council Cutting Du Pont Edith Eightmile Still Ernest Fargo Fivemile Still Homerville Magnolia Sirmans Spooner Traisville Withers

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Fivemile Still, Clinch County, Georgia (2026)