Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Council, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Clinch.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦The current local setback for a metal garage is Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Council, a building permit is required once the garage exceeds No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact. square feet.
- ◦Benton serves Edith, Colon, Ernest and Fargo and other communities around Council.
At a Glance
| Permit threshold |
No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
228
As of 2026 · Source |
Permits & Setbacks in Clinch County
Clinch treats a metal garage like any other accessory structure: under No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact. square feet, Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices. typically doesn't require a full permit, but the Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county. setback rule still governs where it can sit on the lot.
Delivery to Council
Metal garage delivery to Council can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Clinch County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices.. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How close can my metal garage be to the property line?
The current setback in Council is Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county., although you should confirm the requirement for your particular property with Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices.. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Council?
Benton Metal Depot's Statesboro location is approximately 153.6 miles from Council. The company serves residents throughout Clinch, including communities such as Edith, Colon, Ernest and Fargo. Current delivery time for a metal garage to the Council area is about 1 to 2 weeks.
How long does it take to get a metal garage delivered to Council?
Current delivery time to Council is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Council before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Council, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices. has requirements that can affect garage placement, including a current setback of Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Definitions
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Council, Clinch County — At a Glance
- Permit Authority Name
- Clinch County government (Homerville, GA) — no dedicated online building/permitting department page was found; permits appear to be administered out of the county administration/tax assessor offices.
- Permit Authority Url
- https://clinchcountyga.gov/contact.html
- Permit Threshold Sqft
- No explicit sqft exemption found published on the county site. Georgia's statewide-adopted 2024 IRC (effective 1/1/2026) provides a default baseline exemption for one-story detached accessory structures of 200 sq ft or less (Section R105.2) unless a county amends it lower — not confirmed whether Clinch County has a local amendment. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no zoning ordinance or setback table for Clinch County was locatable online (Municode/Zoneomics do not carry a Clinch County entry). A 2018 Georgia GOMI survey lists Clinch as having adopted a zoning ordinance, but the ordinance text itself was not found. Needs direct confirmation with the county.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 153.6
- Drive Minutes
- 228
- Nearby Towns
- Edith, Colon, Ernest, Fargo
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Council and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Council?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://clinchcountyga.gov/contact.html (2026)
- Georgia adoption of 2024 IRC with GA Amendments (statewide baseline); no Clinch County-specific ordinance located online (2026)
- https://georgiaplanning.com/documents/atlas/GOMI_zoning.pdf (lists Clinch among counties with a zoning ordinance, but does not publish the ordinance text) (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Clinch County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Clinch County is deep inland South Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
