Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Eden, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Effingham and the surrounding area.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Eden is currently estimated at 1 to 2 weeks.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Benton Metal Depot is approximately 34.8 miles from Eden.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
At a Glance
| Permit threshold |
Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing.
As of 2026 · Source |
| Wind load zone |
Effingham County borders Chatham County (Savannah) and sits fairly close to the coast — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's range given proximity to the coast. NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
48
As of 2026 · Source |
Permits & Setbacks in Effingham County
Effingham's permitting office, Effingham County Building & Fire Inspection Services, sets the accessory-structure line at Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number. square feet — build under that and you generally skip the full building-permit process, though a setback of 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Eden
Metal garage delivery to Eden can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Effingham County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How close can my metal garage be to the property line?
The current setback in Eden is 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing., although you should confirm the requirement for your particular property with Effingham County Building & Fire Inspection Services. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Effingham County Building & Fire Inspection Services has requirements that can affect garage placement, including a current setback of 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How far is Benton Metal Depot from Eden?
Benton Metal Depot's Statesboro location is approximately 34.8 miles from Eden. The company serves residents throughout Effingham, including communities such as Meldrim, Bloomingdale, Olney and Black Creek. Current delivery time for a metal garage to the Eden area is about 1 to 2 weeks.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
How long does it take to get a metal garage delivered to Eden?
Current delivery time to Eden is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Eden before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Eden, Effingham County — At a Glance
- Permit Authority Name
- Effingham County Building & Fire Inspection Services
- Permit Authority Url
- https://www.effinghamcounty.org/226/Building-Inspections
- Permit Threshold Sqft
- Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number.
- Setback Feet Side Rear
- 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing.
- Wind Load Zone
- Effingham County borders Chatham County (Savannah) and sits fairly close to the coast — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's range given proximity to the coast. NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 34.8
- Drive Minutes
- 48
- Nearby Towns
- Meldrim, Bloomingdale, Olney, Black Creek
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Eden and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Eden?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.effinghamcounty.org/226/Building-Inspections (2026)
- https://www.effinghamcounty.org/DocumentCenter/View/4831/2021-010-Amendment-Part-II-Appendix-C-Art-III-Sec-3-3-Accessory-Building (2026)
- General ASCE 7 near-coastal-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Effingham County is not among the coastal counties named in the client spec, though it directly borders Chatham County (Savannah) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
