Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Marlow, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Effingham.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton Metal Depot is approximately 31 miles from Marlow.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Delivery to Marlow is currently estimated at 1 to 2 weeks.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing.
As of 2026 · Source |
| Wind load zone |
Effingham County borders Chatham County (Savannah) and sits fairly close to the coast — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's range given proximity to the coast. NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
53
As of 2026 · Source |
Permits & Setbacks in Effingham County
The permit question for a Marlow metal garage comes down to one number from Effingham County Building & Fire Inspection Services: Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number. square feet. Stay under it and skip the full permit process; either way, keep the 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing. setback in mind before you pick a spot.
Delivery to Marlow
Metal garage delivery to Marlow can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Effingham County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Marlow before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Marlow?
Current delivery time to Marlow is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Effingham County Building & Fire Inspection Services has requirements that can affect garage placement, including a current setback of 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How far is Benton Metal Depot from Marlow?
Benton Metal Depot's Statesboro location is approximately 31 miles from Marlow. The company serves residents throughout Effingham, including communities such as Egypt, Tusculum, Pineora and Guyton. Current delivery time for a metal garage to the Marlow area is about 1 to 2 weeks.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
How close can my metal garage be to the property line?
The current setback in Marlow is 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing., although you should confirm the requirement for your particular property with Effingham County Building & Fire Inspection Services. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
Marlow, Effingham County — At a Glance
- Permit Authority Name
- Effingham County Building & Fire Inspection Services
- Permit Authority Url
- https://www.effinghamcounty.org/226/Building-Inspections
- Permit Threshold Sqft
- Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number.
- Setback Feet Side Rear
- 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing.
- Wind Load Zone
- Effingham County borders Chatham County (Savannah) and sits fairly close to the coast — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's range given proximity to the coast. NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 31
- Drive Minutes
- 53
- Nearby Towns
- Egypt, Tusculum, Pineora, Guyton
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Marlow and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Marlow?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.effinghamcounty.org/226/Building-Inspections (2026)
- https://www.effinghamcounty.org/DocumentCenter/View/4831/2021-010-Amendment-Part-II-Appendix-C-Art-III-Sec-3-3-Accessory-Building (2026)
- General ASCE 7 near-coastal-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Effingham County is not among the coastal counties named in the client spec, though it directly borders Chatham County (Savannah) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
