Reviewed by the Benton Metal Depot team · Updated
For some residents in Exley, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Effingham, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Delivery to Exley is currently estimated at 1 to 2 weeks.
- ◦Benton Metal Depot is approximately 46.3 miles from Exley.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
At a Glance
| Permit threshold |
Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing.
As of 2026 · Source |
| Wind load zone |
Effingham County borders Chatham County (Savannah) and sits fairly close to the coast — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's range given proximity to the coast. NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
64
As of 2026 · Source |
Permits & Setbacks in Effingham County
Effingham treats a metal garage like any other accessory structure: under Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number. square feet, Effingham County Building & Fire Inspection Services typically doesn't require a full permit, but the 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing. setback rule still governs where it can sit on the lot.
Delivery to Exley
The current estimate for getting a metal garage to Exley is 1 to 2 weeks. The area is about 46.3 miles (64 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Effingham County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Do I need a permit for a metal garage in Exley?
That depends on the garage and the requirements of Effingham County Building & Fire Inspection Services. The current rule requires a permit once the garage exceeds Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Exley, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Effingham County Building & Fire Inspection Services. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How close can my metal garage be to the property line?
The current setback in Exley is 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing., although you should confirm the requirement for your particular property with Effingham County Building & Fire Inspection Services. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Exley, Effingham County — At a Glance
- Permit Authority Name
- Effingham County Building & Fire Inspection Services
- Permit Authority Url
- https://www.effinghamcounty.org/226/Building-Inspections
- Permit Threshold Sqft
- Not explicitly published on the county's Building Inspections page ("a permit is required for any owner...who intends to construct...a building or structure," with no stated sqft carve-out). A 200 sq ft exemption is a common Georgia default (confirmed on record for neighboring Wayne and Burke counties), but this has NOT been confirmed as Effingham's own adopted threshold — contact Effingham County Building & Fire Inspection Services (912-754-2128) to confirm before publishing a number.
- Setback Feet Side Rear
- 5 ft from rear and side property lines for accessory buildings (vs. 10 ft minimum for principal residential structures), per Effingham County's zoning ordinance accessory-building amendment. Corroborated by a local realtor summary but should be verified against the primary ordinance text before publishing.
- Wind Load Zone
- Effingham County borders Chatham County (Savannah) and sits fairly close to the coast — roughly 120-140 mph (ASCE 7, Exposure C), likely toward the higher end of Georgia's range given proximity to the coast. NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 46.3
- Drive Minutes
- 64
- Nearby Towns
- Blandford, Birds, Coldbrook, Rahns
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Exley and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Exley?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.effinghamcounty.org/226/Building-Inspections (2026)
- https://www.effinghamcounty.org/DocumentCenter/View/4831/2021-010-Amendment-Part-II-Appendix-C-Art-III-Sec-3-3-Accessory-Building (2026)
- General ASCE 7 near-coastal-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Effingham County is not among the coastal counties named in the client spec, though it directly borders Chatham County (Savannah) (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
